Fri, 05/01/2009 - 14:55

SEMA News - May 2009

By Drew Hardin
Photo Courtesy Source Interlink Media Archives

 

Mines Field

SEMA News-May 2009-SEMA HeritageYears before Bill France Sr. organized stock car racing on Florida’s most famous beach, stock cars of a different sort went wheel to wheel on tracks around the country. The idea was to pit cars in showroom-floor tune—primarily Fords, as it turned out— against one another to demonstrate their performance chops for prospective buyers. Think of it as “win on Sunday, sell on Monday,” the early years.

One of those races, the Gilmore Gold Cup, was held in February 1934 on a 1.9-mile track at Mines Field in Los Angeles, an area that’s now part of the Los Angeles International Airport. Some 60,000–75,000 people turned out to watch the 250-mile event, which took four hours to finish. Stubby Stubblefield’s ’33 Ford roadster was declared the Gold Cup winner, with an average speed of 62.37 mph.

Another Mines Field entrant was this ’34 Ford roadster driven by Shorty Cantlon and sponsored by W. I. Tupman, then a downtown Los Angeles Ford dealer. We haven’t been able to dig up Shorty’s results, but his hot iron displays many of the speed tricks typical of the era. To get the most out of the Flathead V8—left bone stock per the AAA, the race’s sanctioning body—the ’34 was streamlined and lightened by removing its fenders, running boards, bumpers, lights, windshield and more. The resulting iconic look has been imitated by hot rodders and abetted by SEMA members ever since.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

By Linda Spencer

 

New U.S. Government Regulation Impacts All Companies Importing Product into the United States

SEMA News-May-2009-International

Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders.

Importing product into the United States just became more complicated and costly due to a new U.S. Customs and Border Protection (CBP) regulation. The Importer Security Filing (ISF), which is commonly known as the “10+2” initiative (because it requires importers to supply 10 pieces of data and shipping companies another two items), marks the first time importers are required to communicate with the CBP regarding incoming shipments.

All importers—from those bringing in one container a year to those importing products weekly—are equally liable under this new rule, which took effect January 26, 2009, and mandates that importers or their designated agents supply the required data electronically at a minimum of 24 hours before the products are loaded onto ships in the overseas port. Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders. The CBP is delaying enforcement for one year in order to allow companies time to implement compliant systems.

Information required includes 1) importer of record number; 2) consignee number; 3) seller (owner) name/address; 4) buyer (owner) name/address; 5) ship-to party; 6) manufacturer (supplier) name/address; 7) country of origin; 8) Commodity Harmonized Tariff Schedule number (must be submitted 24 hours prior to the product being loaded onto the ship); 9) container stuffing location; and 10) consolidator name/address.

The 10+2 initiative has been developed as part of CBP’s ongoing strategy to assess and identify high-risk shipments so as to prevent smuggling and ensure cargo safety and security.

In response to concerns raised by industry and lawmakers on Capitol Hill over the likely additional costs and delays importers would be subject to as a direct result of the rule and the fact that much is unknown as to whether importers will be able to supply the data in the timeframe required, the CBP agreed to keep the comment period open through the end of July 2009. SEMA, as part of a coalition of businesses, has called for a longer comment period to document compliance issues that arise as companies begin to meet the 10+2 requirements.

Because setting up a CBP-compliant electronic transmittal system is said to cost in the range of $25,000 (CBP estimate) for the initial setup charges, most small- and medium-size importers will find that the only feasible option is to pay a third party, such as a broker, to conduct the filing on their behalf. Brokers have been announcing fee increases to file the new data element requirements. The additional costs vary greatly, with the most often-heard estimates of $50–$200 per shipment.

Continual updating of the data submitted to the CBP is required. The ISF must be amended if there is a change or more accurate information becomes available before the goods enter the U.S. port, but after the initial filing, thus increasing the likely broker fees as well.

SEMA News-May 2009-International

Attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Most importers do not have access to the data in all 10 categories required for importers 24 hours in advance of loading containers onto vessels in foreign ports. Some of this information is uniquely known to various parties within the supply chain. Among the parties having sole information on one or more of the required data elements are manufacturers, suppliers, carriers, WDs and retailers, which typically fit into three groups, including those parties: 1) involved in the order and manufacture of goods; 2) involved in the preparation and arrangement of goods for shipment; and 3) involved in the shipment and customs clearance of goods from the foreign port to the United States.

The CBP acknowledges this and notes that importers might have particular difficulty complying with four of the required items during the 24 hours prior to ship loading, including manufacturer supplier, ship-to party, country of origin and commodity HTSUS number. Additionally, the CBP admits that there may be no data available at all during the 24 hours prior to lading for two additional items: container stuffing location and consolidator (stuffer) name/address. For the first group of items, the government agrees during the period of the interim rule for companies to submit partial information, which would need to be updated as information becomes available. For the last two items, the government extends the allowable reporting period up to 24 hours before the product arrives in the United States.

The complete and timely submittal of the importer data elements may be more problematic for shipments that are consolidated in containers. For such shipments, the supply chain is generally more complex and the importer has less control of the flow of goods and associated security filing information. The consolidator may be consolidating multiple shipments from one or more shippers in a container destined for one or more customers. It may be necessary for consolidators to advance their cutoff deadlines in order to ensure that the security filing data is provided by the shippers to the importers (or their designated agents) and is then transmitted to and accepted by CBP in advance of the 24-hour deadline.

While the CBP has said that it is delaying penalties for one year, it has provided itself with the legal wiggle room to impose them sooner based on “lack of effort” on the part of importers. Specifically, the interim rule notes that the CBP will “show restraint in enforcing the rule, taking into account difficulties that importers may face in complying with the rule, so long as importers are making satisfactory progress toward compliance and are making a good-faith effort to comply with the rule to the extent of their current ability.”

In addition, attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Additional information on 10+2 is available at www.sema.org/international or by contacting Linda Spencer at lindas@sema.org.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

By Linda Spencer

 

New U.S. Government Regulation Impacts All Companies Importing Product into the United States

SEMA News-May-2009-International

Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders.

Importing product into the United States just became more complicated and costly due to a new U.S. Customs and Border Protection (CBP) regulation. The Importer Security Filing (ISF), which is commonly known as the “10+2” initiative (because it requires importers to supply 10 pieces of data and shipping companies another two items), marks the first time importers are required to communicate with the CBP regarding incoming shipments.

All importers—from those bringing in one container a year to those importing products weekly—are equally liable under this new rule, which took effect January 26, 2009, and mandates that importers or their designated agents supply the required data electronically at a minimum of 24 hours before the products are loaded onto ships in the overseas port. Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders. The CBP is delaying enforcement for one year in order to allow companies time to implement compliant systems.

Information required includes 1) importer of record number; 2) consignee number; 3) seller (owner) name/address; 4) buyer (owner) name/address; 5) ship-to party; 6) manufacturer (supplier) name/address; 7) country of origin; 8) Commodity Harmonized Tariff Schedule number (must be submitted 24 hours prior to the product being loaded onto the ship); 9) container stuffing location; and 10) consolidator name/address.

The 10+2 initiative has been developed as part of CBP’s ongoing strategy to assess and identify high-risk shipments so as to prevent smuggling and ensure cargo safety and security.

In response to concerns raised by industry and lawmakers on Capitol Hill over the likely additional costs and delays importers would be subject to as a direct result of the rule and the fact that much is unknown as to whether importers will be able to supply the data in the timeframe required, the CBP agreed to keep the comment period open through the end of July 2009. SEMA, as part of a coalition of businesses, has called for a longer comment period to document compliance issues that arise as companies begin to meet the 10+2 requirements.

Because setting up a CBP-compliant electronic transmittal system is said to cost in the range of $25,000 (CBP estimate) for the initial setup charges, most small- and medium-size importers will find that the only feasible option is to pay a third party, such as a broker, to conduct the filing on their behalf. Brokers have been announcing fee increases to file the new data element requirements. The additional costs vary greatly, with the most often-heard estimates of $50–$200 per shipment.

Continual updating of the data submitted to the CBP is required. The ISF must be amended if there is a change or more accurate information becomes available before the goods enter the U.S. port, but after the initial filing, thus increasing the likely broker fees as well.

SEMA News-May 2009-International

Attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Most importers do not have access to the data in all 10 categories required for importers 24 hours in advance of loading containers onto vessels in foreign ports. Some of this information is uniquely known to various parties within the supply chain. Among the parties having sole information on one or more of the required data elements are manufacturers, suppliers, carriers, WDs and retailers, which typically fit into three groups, including those parties: 1) involved in the order and manufacture of goods; 2) involved in the preparation and arrangement of goods for shipment; and 3) involved in the shipment and customs clearance of goods from the foreign port to the United States.

The CBP acknowledges this and notes that importers might have particular difficulty complying with four of the required items during the 24 hours prior to ship loading, including manufacturer supplier, ship-to party, country of origin and commodity HTSUS number. Additionally, the CBP admits that there may be no data available at all during the 24 hours prior to lading for two additional items: container stuffing location and consolidator (stuffer) name/address. For the first group of items, the government agrees during the period of the interim rule for companies to submit partial information, which would need to be updated as information becomes available. For the last two items, the government extends the allowable reporting period up to 24 hours before the product arrives in the United States.

The complete and timely submittal of the importer data elements may be more problematic for shipments that are consolidated in containers. For such shipments, the supply chain is generally more complex and the importer has less control of the flow of goods and associated security filing information. The consolidator may be consolidating multiple shipments from one or more shippers in a container destined for one or more customers. It may be necessary for consolidators to advance their cutoff deadlines in order to ensure that the security filing data is provided by the shippers to the importers (or their designated agents) and is then transmitted to and accepted by CBP in advance of the 24-hour deadline.

While the CBP has said that it is delaying penalties for one year, it has provided itself with the legal wiggle room to impose them sooner based on “lack of effort” on the part of importers. Specifically, the interim rule notes that the CBP will “show restraint in enforcing the rule, taking into account difficulties that importers may face in complying with the rule, so long as importers are making satisfactory progress toward compliance and are making a good-faith effort to comply with the rule to the extent of their current ability.”

In addition, attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Additional information on 10+2 is available at www.sema.org/international or by contacting Linda Spencer at lindas@sema.org.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

By Linda Spencer

 

New U.S. Government Regulation Impacts All Companies Importing Product into the United States

SEMA News-May-2009-International

Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders.

Importing product into the United States just became more complicated and costly due to a new U.S. Customs and Border Protection (CBP) regulation. The Importer Security Filing (ISF), which is commonly known as the “10+2” initiative (because it requires importers to supply 10 pieces of data and shipping companies another two items), marks the first time importers are required to communicate with the CBP regarding incoming shipments.

All importers—from those bringing in one container a year to those importing products weekly—are equally liable under this new rule, which took effect January 26, 2009, and mandates that importers or their designated agents supply the required data electronically at a minimum of 24 hours before the products are loaded onto ships in the overseas port. Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders. The CBP is delaying enforcement for one year in order to allow companies time to implement compliant systems.

Information required includes 1) importer of record number; 2) consignee number; 3) seller (owner) name/address; 4) buyer (owner) name/address; 5) ship-to party; 6) manufacturer (supplier) name/address; 7) country of origin; 8) Commodity Harmonized Tariff Schedule number (must be submitted 24 hours prior to the product being loaded onto the ship); 9) container stuffing location; and 10) consolidator name/address.

The 10+2 initiative has been developed as part of CBP’s ongoing strategy to assess and identify high-risk shipments so as to prevent smuggling and ensure cargo safety and security.

In response to concerns raised by industry and lawmakers on Capitol Hill over the likely additional costs and delays importers would be subject to as a direct result of the rule and the fact that much is unknown as to whether importers will be able to supply the data in the timeframe required, the CBP agreed to keep the comment period open through the end of July 2009. SEMA, as part of a coalition of businesses, has called for a longer comment period to document compliance issues that arise as companies begin to meet the 10+2 requirements.

Because setting up a CBP-compliant electronic transmittal system is said to cost in the range of $25,000 (CBP estimate) for the initial setup charges, most small- and medium-size importers will find that the only feasible option is to pay a third party, such as a broker, to conduct the filing on their behalf. Brokers have been announcing fee increases to file the new data element requirements. The additional costs vary greatly, with the most often-heard estimates of $50–$200 per shipment.

Continual updating of the data submitted to the CBP is required. The ISF must be amended if there is a change or more accurate information becomes available before the goods enter the U.S. port, but after the initial filing, thus increasing the likely broker fees as well.

SEMA News-May 2009-International

Attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Most importers do not have access to the data in all 10 categories required for importers 24 hours in advance of loading containers onto vessels in foreign ports. Some of this information is uniquely known to various parties within the supply chain. Among the parties having sole information on one or more of the required data elements are manufacturers, suppliers, carriers, WDs and retailers, which typically fit into three groups, including those parties: 1) involved in the order and manufacture of goods; 2) involved in the preparation and arrangement of goods for shipment; and 3) involved in the shipment and customs clearance of goods from the foreign port to the United States.

The CBP acknowledges this and notes that importers might have particular difficulty complying with four of the required items during the 24 hours prior to ship loading, including manufacturer supplier, ship-to party, country of origin and commodity HTSUS number. Additionally, the CBP admits that there may be no data available at all during the 24 hours prior to lading for two additional items: container stuffing location and consolidator (stuffer) name/address. For the first group of items, the government agrees during the period of the interim rule for companies to submit partial information, which would need to be updated as information becomes available. For the last two items, the government extends the allowable reporting period up to 24 hours before the product arrives in the United States.

The complete and timely submittal of the importer data elements may be more problematic for shipments that are consolidated in containers. For such shipments, the supply chain is generally more complex and the importer has less control of the flow of goods and associated security filing information. The consolidator may be consolidating multiple shipments from one or more shippers in a container destined for one or more customers. It may be necessary for consolidators to advance their cutoff deadlines in order to ensure that the security filing data is provided by the shippers to the importers (or their designated agents) and is then transmitted to and accepted by CBP in advance of the 24-hour deadline.

While the CBP has said that it is delaying penalties for one year, it has provided itself with the legal wiggle room to impose them sooner based on “lack of effort” on the part of importers. Specifically, the interim rule notes that the CBP will “show restraint in enforcing the rule, taking into account difficulties that importers may face in complying with the rule, so long as importers are making satisfactory progress toward compliance and are making a good-faith effort to comply with the rule to the extent of their current ability.”

In addition, attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Additional information on 10+2 is available at www.sema.org/international or by contacting Linda Spencer at lindas@sema.org.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

By Linda Spencer

 

New U.S. Government Regulation Impacts All Companies Importing Product into the United States

SEMA News-May-2009-International

Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders.

Importing product into the United States just became more complicated and costly due to a new U.S. Customs and Border Protection (CBP) regulation. The Importer Security Filing (ISF), which is commonly known as the “10+2” initiative (because it requires importers to supply 10 pieces of data and shipping companies another two items), marks the first time importers are required to communicate with the CBP regarding incoming shipments.

All importers—from those bringing in one container a year to those importing products weekly—are equally liable under this new rule, which took effect January 26, 2009, and mandates that importers or their designated agents supply the required data electronically at a minimum of 24 hours before the products are loaded onto ships in the overseas port. Penalties for incomplete or non-compliance are steep—$5,000 per incident as well as possible no-load orders. The CBP is delaying enforcement for one year in order to allow companies time to implement compliant systems.

Information required includes 1) importer of record number; 2) consignee number; 3) seller (owner) name/address; 4) buyer (owner) name/address; 5) ship-to party; 6) manufacturer (supplier) name/address; 7) country of origin; 8) Commodity Harmonized Tariff Schedule number (must be submitted 24 hours prior to the product being loaded onto the ship); 9) container stuffing location; and 10) consolidator name/address.

The 10+2 initiative has been developed as part of CBP’s ongoing strategy to assess and identify high-risk shipments so as to prevent smuggling and ensure cargo safety and security.

In response to concerns raised by industry and lawmakers on Capitol Hill over the likely additional costs and delays importers would be subject to as a direct result of the rule and the fact that much is unknown as to whether importers will be able to supply the data in the timeframe required, the CBP agreed to keep the comment period open through the end of July 2009. SEMA, as part of a coalition of businesses, has called for a longer comment period to document compliance issues that arise as companies begin to meet the 10+2 requirements.

Because setting up a CBP-compliant electronic transmittal system is said to cost in the range of $25,000 (CBP estimate) for the initial setup charges, most small- and medium-size importers will find that the only feasible option is to pay a third party, such as a broker, to conduct the filing on their behalf. Brokers have been announcing fee increases to file the new data element requirements. The additional costs vary greatly, with the most often-heard estimates of $50–$200 per shipment.

Continual updating of the data submitted to the CBP is required. The ISF must be amended if there is a change or more accurate information becomes available before the goods enter the U.S. port, but after the initial filing, thus increasing the likely broker fees as well.

SEMA News-May 2009-International

Attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Most importers do not have access to the data in all 10 categories required for importers 24 hours in advance of loading containers onto vessels in foreign ports. Some of this information is uniquely known to various parties within the supply chain. Among the parties having sole information on one or more of the required data elements are manufacturers, suppliers, carriers, WDs and retailers, which typically fit into three groups, including those parties: 1) involved in the order and manufacture of goods; 2) involved in the preparation and arrangement of goods for shipment; and 3) involved in the shipment and customs clearance of goods from the foreign port to the United States.

The CBP acknowledges this and notes that importers might have particular difficulty complying with four of the required items during the 24 hours prior to ship loading, including manufacturer supplier, ship-to party, country of origin and commodity HTSUS number. Additionally, the CBP admits that there may be no data available at all during the 24 hours prior to lading for two additional items: container stuffing location and consolidator (stuffer) name/address. For the first group of items, the government agrees during the period of the interim rule for companies to submit partial information, which would need to be updated as information becomes available. For the last two items, the government extends the allowable reporting period up to 24 hours before the product arrives in the United States.

The complete and timely submittal of the importer data elements may be more problematic for shipments that are consolidated in containers. For such shipments, the supply chain is generally more complex and the importer has less control of the flow of goods and associated security filing information. The consolidator may be consolidating multiple shipments from one or more shippers in a container destined for one or more customers. It may be necessary for consolidators to advance their cutoff deadlines in order to ensure that the security filing data is provided by the shippers to the importers (or their designated agents) and is then transmitted to and accepted by CBP in advance of the 24-hour deadline.

While the CBP has said that it is delaying penalties for one year, it has provided itself with the legal wiggle room to impose them sooner based on “lack of effort” on the part of importers. Specifically, the interim rule notes that the CBP will “show restraint in enforcing the rule, taking into account difficulties that importers may face in complying with the rule, so long as importers are making satisfactory progress toward compliance and are making a good-faith effort to comply with the rule to the extent of their current ability.”

In addition, attempting compliance at this stage allows the input of SEMA members into the difficulties and costs incurred in complying with this program during the open-comment period.

Additional information on 10+2 is available at www.sema.org/international or by contacting Linda Spencer at lindas@sema.org.

Fri, 05/01/2009 - 14:55

 SEMA News - May 2009

By Joe Dysart

A Wider Reach for Company News

SEMA News-May 2009-Internet

One of the best examples of a web 2.0-enabled press release in action can be found at Marketwire.

With business communications moving at the speed of fiber-optic light for years now, it’s no wonder that the humble press release has finally caught up. Shaking off its dead-tree past for good, today’s reinvented press release is packed with a number of web 2.0 elements that make it much more interactive and, as some of the digerati might say, much more “web-viral ready.”

Readers accustomed to posting their opinions in blogs, MySpace, Amazon product-review forums and the like, for example, can now do the same on web 2.0 press releases, which sport their own “comments” sections right on the release. Info junkies, who regularly bookmark and share interesting news and other items on the dozens of social bookmarking sites that have sprung up on the web are given tools with a web 2.0-enabled press release that allow them to quickly bookmark the release with a service of their choice. And bloggers, who thrive on arcane tools, such as “permalinks” and “trackbacks” to make it easier for the blogosphere to seamlessly discuss breaking news, are pleasantly surprised to find that web 2.0-enabled press releases have these tools built in.

“In the last two years, there has been a sea of change in how the press release is viewed and utilized,” said Paolina Milana, vice president of marketing at Marketwire. “The once 400-word, all-text release has evolved into an interactive tool that incorporates multimedia elements, social media tags and bookmarks, in-release performance stats and feedback mechanisms.”

Brian Solis, principal at PR firm FutureWorks agrees: “It’s something that combines the best of traditional, new and social media and helps package a story in a way that works for different writers and users.”

One of the best examples of a web 2.0-enabled press release in action can be found here at Marketwire—a format that deftly incorporates virtually every web 2.0 tool you’d ever want in a press release on a single page. You can go to Marketwire for your own web 2.0-enabled press release, or you can simply put one together yourself. The following items are the key elements you’ll want to include.

Comments Capability: Enabling readers to post comments on your press release—the same way they post comments on a blog—can give the announcement more legs. A journalist or blogger who posts a comment on your release, for example, may in turn attract other journalists, bloggers and readers to your release, and so on. The feature also works as a consumer tool that makes it easier for the public to identify and share interesting content in the social networking communities, said Deirdre Breakenridge, author of PR 2.0 and president of PFS Marketwyse, a PR firm.

SEMA News-May 2009-Internet
Free tools, such as “AddThis,” enable you to offer links to more than three dozen social bookmarking services.

Social Bookmark-Friendly: There’s an entire subculture of info and news junkies on the web who regularly categorize and bookmark items of interest for themselves on free bookmarking services, such as Delicious.com and Digg.com. Adding quick links to these bookmarking services, which members use to store and share their links with others, offers your press release another opportunity to reach a wider audience. Free tools, such as “AddThis”, enable you to offer quick links to more than three dozen social bookmarking services.

Link-to-This-Page Button: This tool makes it effortless for a journalist, blogger or other reader to link to your press release from another website, article or blog. I regularly link to press releases, company PDFs and similar company info on the web in the articles I write.

E-mail This Page to a Friend: By now, most companies understand the power of word-of-mouth referrals on the web and have been using this tool on other pages of their websites. Including this tool on every web -based press release also helps.

Permalink: This is a fancy term for a link that will never be changed or moved. It’s the perfect solution for companies that like to feature new press releases on their homepages (a temporary location) while simultaneously storing the same press release in their archives (a permalink location). Journalists, bloggers and other opinion shapers like to include permalinks in their work on the web, since they can be reasonably confident that those links will last indefinitely.

Trackbacks: A product of the blogosphere, trackbacks are little snippets of code that let you know people are talking about your press release on another blog. In practice, the commenter—usually a blogger—cuts and pastes your trackback code into his blogging program, and the comment alert is sent back to your company press center. You can find a detailed description of trackbacks at “How Trackbacks Work”

Supporting Images/Video Links: There’s never been a better time to feature links to supporting digital images and video for a press release. The mainstream media is always hungry for news images; bloggers are even hungrier. In addition to offering standard links to images of corporate executives, you can also offer links to web video associated with the press release and to related web videos you’ve posted on YouTube.

Other Company Press Releases Link: A quick link to your company’s press release domain makes it easier for journalists and bloggers to easily dig deeper into the story.

Company Press Center Link: Offering an easy way for readers to get to the heart of your company’s publicity apparatus is another no-brainer.

Press Release RSS: A significant percentage of news hounds and info junkies now gather much of their news off the web with RSS (Really Simple Syndication) readers. An RSS reader is a lot like an e-mail reader, only it’s generally tougher to spam, which is why many info junkies prefer the technology. Your web designer will know how to quickly code your press release for RSS. Or you can auto-code a press release yourself in about five minutes with Ice Rocket’s free RSS Builder tool.

Joe Dysart is an Internet speaker and business consultant based in Manhattan, New York.
Voice: 646/233-4089
E-mail: joe@joedysart.com
Website: http://www.joedysart.com/

Fri, 05/01/2009 - 14:55

 SEMA News - May 2009

By Joe Dysart

A Wider Reach for Company News

SEMA News-May 2009-Internet

One of the best examples of a web 2.0-enabled press release in action can be found at Marketwire.

With business communications moving at the speed of fiber-optic light for years now, it’s no wonder that the humble press release has finally caught up. Shaking off its dead-tree past for good, today’s reinvented press release is packed with a number of web 2.0 elements that make it much more interactive and, as some of the digerati might say, much more “web-viral ready.”

Readers accustomed to posting their opinions in blogs, MySpace, Amazon product-review forums and the like, for example, can now do the same on web 2.0 press releases, which sport their own “comments” sections right on the release. Info junkies, who regularly bookmark and share interesting news and other items on the dozens of social bookmarking sites that have sprung up on the web are given tools with a web 2.0-enabled press release that allow them to quickly bookmark the release with a service of their choice. And bloggers, who thrive on arcane tools, such as “permalinks” and “trackbacks” to make it easier for the blogosphere to seamlessly discuss breaking news, are pleasantly surprised to find that web 2.0-enabled press releases have these tools built in.

“In the last two years, there has been a sea of change in how the press release is viewed and utilized,” said Paolina Milana, vice president of marketing at Marketwire. “The once 400-word, all-text release has evolved into an interactive tool that incorporates multimedia elements, social media tags and bookmarks, in-release performance stats and feedback mechanisms.”

Brian Solis, principal at PR firm FutureWorks agrees: “It’s something that combines the best of traditional, new and social media and helps package a story in a way that works for different writers and users.”

One of the best examples of a web 2.0-enabled press release in action can be found here at Marketwire—a format that deftly incorporates virtually every web 2.0 tool you’d ever want in a press release on a single page. You can go to Marketwire for your own web 2.0-enabled press release, or you can simply put one together yourself. The following items are the key elements you’ll want to include.

Comments Capability: Enabling readers to post comments on your press release—the same way they post comments on a blog—can give the announcement more legs. A journalist or blogger who posts a comment on your release, for example, may in turn attract other journalists, bloggers and readers to your release, and so on. The feature also works as a consumer tool that makes it easier for the public to identify and share interesting content in the social networking communities, said Deirdre Breakenridge, author of PR 2.0 and president of PFS Marketwyse, a PR firm.

SEMA News-May 2009-Internet
Free tools, such as “AddThis,” enable you to offer links to more than three dozen social bookmarking services.

Social Bookmark-Friendly: There’s an entire subculture of info and news junkies on the web who regularly categorize and bookmark items of interest for themselves on free bookmarking services, such as Delicious.com and Digg.com. Adding quick links to these bookmarking services, which members use to store and share their links with others, offers your press release another opportunity to reach a wider audience. Free tools, such as “AddThis”, enable you to offer quick links to more than three dozen social bookmarking services.

Link-to-This-Page Button: This tool makes it effortless for a journalist, blogger or other reader to link to your press release from another website, article or blog. I regularly link to press releases, company PDFs and similar company info on the web in the articles I write.

E-mail This Page to a Friend: By now, most companies understand the power of word-of-mouth referrals on the web and have been using this tool on other pages of their websites. Including this tool on every web -based press release also helps.

Permalink: This is a fancy term for a link that will never be changed or moved. It’s the perfect solution for companies that like to feature new press releases on their homepages (a temporary location) while simultaneously storing the same press release in their archives (a permalink location). Journalists, bloggers and other opinion shapers like to include permalinks in their work on the web, since they can be reasonably confident that those links will last indefinitely.

Trackbacks: A product of the blogosphere, trackbacks are little snippets of code that let you know people are talking about your press release on another blog. In practice, the commenter—usually a blogger—cuts and pastes your trackback code into his blogging program, and the comment alert is sent back to your company press center. You can find a detailed description of trackbacks at “How Trackbacks Work”

Supporting Images/Video Links: There’s never been a better time to feature links to supporting digital images and video for a press release. The mainstream media is always hungry for news images; bloggers are even hungrier. In addition to offering standard links to images of corporate executives, you can also offer links to web video associated with the press release and to related web videos you’ve posted on YouTube.

Other Company Press Releases Link: A quick link to your company’s press release domain makes it easier for journalists and bloggers to easily dig deeper into the story.

Company Press Center Link: Offering an easy way for readers to get to the heart of your company’s publicity apparatus is another no-brainer.

Press Release RSS: A significant percentage of news hounds and info junkies now gather much of their news off the web with RSS (Really Simple Syndication) readers. An RSS reader is a lot like an e-mail reader, only it’s generally tougher to spam, which is why many info junkies prefer the technology. Your web designer will know how to quickly code your press release for RSS. Or you can auto-code a press release yourself in about five minutes with Ice Rocket’s free RSS Builder tool.

Joe Dysart is an Internet speaker and business consultant based in Manhattan, New York.
Voice: 646/233-4089
E-mail: joe@joedysart.com
Website: http://www.joedysart.com/

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

RESEARCH

By Oscar Muñoz

Computer Tools for Design

Making the Most of Technology

SEMA News-May 2009-Research 

CAD systems allow your company to make designs such as this and enable you to take advantage of technologies geared toward bringing your product to market faster, better and at a lower cost.

 
In a recent SEMA survey of specialty-equipment manufacturers, 83% of respondents said that they use computer-aided design (CAD) software as part of their new-product design process. It is an indication that our industry is embracing CAD as it has become more attainable and easy to use due in large part to the constant gains in processing power that today’s PCs provide.

The primary benefit of using CAD is the streamlining it creates for the development of new products, which can be coupled to third-party software tools that extend functionality beyond the basics of mechanical design. Reverse engineering, rapid prototyping and computer-aided manufacturing (CAM) are just a few examples of tools that work within CAD applications to maximize development for any manufacturing organization. We’d like to offer a glimpse at the technologies that are available and can be easily integrated with your CAD software to reduce your research and development and enhance some of your consumer-outreach operations.

MCAD Application

Mechanical computer-aided design/drafting (MCAD) software provides engineers with an array of features that allows them to more easily develop products. At the core of each application is a modeling feature that lets the user create sketches from which a 3-D component will be produced. Generally speaking, most designs begin from a 2-D sketch and progress from there into a final design once depth and details are worked in. The process can be time-consuming, particularly if the model carries high levels of detail. However, the software provides a rich set of tools and wizards that make the process progress smoothly. Fillets, cuts, extrusions, edges, drafts, shells, patterns and ribs are all preset functions available through a button or wizard that simplifies the process. If you’re not sure, a simple click on a pull-down menu will get you started on a tutorial for further guidance.

SEMA News-May 2009-Research  

CAD software helps your company with more than design and manufacturing. In a matter of minutes you can take a CAD drawing (p. 44) and create a photorealistic rendering (above) to increase the appeal of proposals, marketing brochures or presentations—extending its reach into more aspects of your business operations than just R&D.

As you move from part design to assembly modeling, you begin to position and define the relationships between the parts of the assembly. Parts that have a set of motion relations with respect to each component (i.e. sprockets, pulleys, linkages) would be linked with each other so that clicking and dragging any part of the moving set would simulate the corresponding motion among involved parts. This helps identify interference with nearby parts or possible collisions as well as observe and measure relative velocities and accelerations that can be used to further analyze the forces in the system and better engineer the product. Other features of note are bill-of-materials generation and photorealistic rendering. Both not only facilitate communications between the engineer and other departments in the organization, but also provide content that can be used in the development of proposals, presentations and virtual demonstrations of the product, which help reduce the additional costs of having other departments create the material from scratch.

If you’re interested in evaluating a CAD software package, several companies offer free trial versions, including AutoCAD, Rhino3D and SolidWorks.

SEMA News-May 2009-Research

 

A rapid prototyping machine can take your CAD design and provide you with a prototype within one to two days. SEMA uses this model from Dimension Printing to provide rapid prototyping service to its members.
Courtesy Dimension Printing

 

Reverse Engineering

Reverse engineering tools are aids to designing products that will be installed on a vehicle. In order for the parts to fit and function as designed, accurate measurements need to be taken. A two-part combination of tools is needed to easily and effectively capture this data and import it into your CAD software. A 3-D measurement tool is used to capture the data from either a part that has been fabricated without CAD or an existing part taken from a vehicle. There are two main types of tools: a contact type, where the machine needs to physically touch the target object being digitized, and a non-contact type, such as a laser scanner or camera that projects light on the target object and captures the reflected light. In either case, the machine establishes a reference frame and sends point coordinates to a connected laptop. Captured data can then be fed to the second part of the tool combination, a specialized software application that will place the dots into a virtual 3-D space and reconstruct the object, identifying key features and constructing them as you would in your CAD software. The result is a precise CAD representation of the object you scanned, ready to use in a fraction of the time it would take without these tools.

There are a number of features and parameters to look for in 3-D measuring tools:

Scan Accuracy–Range from .008-inch to .001-inch; accuracy is determined by comparing the variation between the actual point on the part versus the scanned point.
Scan Rate–Point-and-click (approximately point per second) to upward of 28,000 points per second.
Mobility–Solutions are offered for either fixed-station use or portability.
Size–The size of the components to be digitized may dictate the size of digitizer needed.
Functions to look for in scan-to-CAD software include:
Feature Recognition–Capability to reconstruct the part as a detailed CAD part object, allowing for manipulation through the CAD software tools.
Compatibility–Your CAD software and 3-D measuring tool need to be compatible with the scan-to-CAD software.

Rapid Prototyping

A key phase in the development process is validation of your design through testing. Doing so requires the production of prototypes to be used in evaluating the fit of the part as well as to benchmark and fine-tune the desired functional characteristics. The process is iterative, requiring multiple prototypes, with each implementing a design change or revision to further refine the design. Rapid prototyping enables you to produce prototypes directly from your CAD data, with lead times ranging from one to five days. Rapid prototyping machines build by joining layers of material into a desired shape. The costs for rapid prototypes are relatively low because there is no need to create tooling, and they provide one of the quickest approaches to building prototypes, thereby maximizing time usage.

SEMA News-May 2009-Research

Reverse engineering—This ’32 Ford coupe is captured in 3-D using a 3-D Laser Scanner and Point Cloud software.
Courtesy Konica Minolta

What to look for:

Machine Type–Stereolithography, selective laser sintering, fused deposition modeling, laminated object manufacturing and 3-D printing.
Material–Material selection is dictated by the machine, which includes photopolymer, polyamide material, epoxy-type resin and ABS plastic. Some are better used in form and fit evaluations, while others are strong enough to use in functional testing.
Size Capacity–Build envelopes vary. Packaged software may allow for splitting larger parts into smaller pieces that may be built by the machine.
Layer Thickness–Ranges from .004-inch to .0013-inch.

SEMA currently offers rapid prototyping as an extension of the Technology Transfer program to help introduce the technology’s benefits to its members.

CAM

If your company uses computer numeric control (CNC) machines as part of your manufacturing process, then you may also want to take a look at CAM software options. CNC machines offer repeatable accuracy and efficiency in manufacturing. CAM software analyzes the various part features of your design, identifying machinable surfaces and detecting the best path to take and then creating the program for all types of numerical control machines, including milling, turning, mold and die, multi-axis and more.

While most SEMA members say that they are using CAD, newer tools are available that utilize the drawings and turn traditional manufacturing into a high-tech and money-saving process. These new computer tools make the most of technology.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

RESEARCH

By Oscar Muñoz

Computer Tools for Design

Making the Most of Technology

SEMA News-May 2009-Research 

CAD systems allow your company to make designs such as this and enable you to take advantage of technologies geared toward bringing your product to market faster, better and at a lower cost.

 
In a recent SEMA survey of specialty-equipment manufacturers, 83% of respondents said that they use computer-aided design (CAD) software as part of their new-product design process. It is an indication that our industry is embracing CAD as it has become more attainable and easy to use due in large part to the constant gains in processing power that today’s PCs provide.

The primary benefit of using CAD is the streamlining it creates for the development of new products, which can be coupled to third-party software tools that extend functionality beyond the basics of mechanical design. Reverse engineering, rapid prototyping and computer-aided manufacturing (CAM) are just a few examples of tools that work within CAD applications to maximize development for any manufacturing organization. We’d like to offer a glimpse at the technologies that are available and can be easily integrated with your CAD software to reduce your research and development and enhance some of your consumer-outreach operations.

MCAD Application

Mechanical computer-aided design/drafting (MCAD) software provides engineers with an array of features that allows them to more easily develop products. At the core of each application is a modeling feature that lets the user create sketches from which a 3-D component will be produced. Generally speaking, most designs begin from a 2-D sketch and progress from there into a final design once depth and details are worked in. The process can be time-consuming, particularly if the model carries high levels of detail. However, the software provides a rich set of tools and wizards that make the process progress smoothly. Fillets, cuts, extrusions, edges, drafts, shells, patterns and ribs are all preset functions available through a button or wizard that simplifies the process. If you’re not sure, a simple click on a pull-down menu will get you started on a tutorial for further guidance.

SEMA News-May 2009-Research  

CAD software helps your company with more than design and manufacturing. In a matter of minutes you can take a CAD drawing (p. 44) and create a photorealistic rendering (above) to increase the appeal of proposals, marketing brochures or presentations—extending its reach into more aspects of your business operations than just R&D.

As you move from part design to assembly modeling, you begin to position and define the relationships between the parts of the assembly. Parts that have a set of motion relations with respect to each component (i.e. sprockets, pulleys, linkages) would be linked with each other so that clicking and dragging any part of the moving set would simulate the corresponding motion among involved parts. This helps identify interference with nearby parts or possible collisions as well as observe and measure relative velocities and accelerations that can be used to further analyze the forces in the system and better engineer the product. Other features of note are bill-of-materials generation and photorealistic rendering. Both not only facilitate communications between the engineer and other departments in the organization, but also provide content that can be used in the development of proposals, presentations and virtual demonstrations of the product, which help reduce the additional costs of having other departments create the material from scratch.

If you’re interested in evaluating a CAD software package, several companies offer free trial versions, including AutoCAD, Rhino3D and SolidWorks.

SEMA News-May 2009-Research

 

A rapid prototyping machine can take your CAD design and provide you with a prototype within one to two days. SEMA uses this model from Dimension Printing to provide rapid prototyping service to its members.
Courtesy Dimension Printing

 

Reverse Engineering

Reverse engineering tools are aids to designing products that will be installed on a vehicle. In order for the parts to fit and function as designed, accurate measurements need to be taken. A two-part combination of tools is needed to easily and effectively capture this data and import it into your CAD software. A 3-D measurement tool is used to capture the data from either a part that has been fabricated without CAD or an existing part taken from a vehicle. There are two main types of tools: a contact type, where the machine needs to physically touch the target object being digitized, and a non-contact type, such as a laser scanner or camera that projects light on the target object and captures the reflected light. In either case, the machine establishes a reference frame and sends point coordinates to a connected laptop. Captured data can then be fed to the second part of the tool combination, a specialized software application that will place the dots into a virtual 3-D space and reconstruct the object, identifying key features and constructing them as you would in your CAD software. The result is a precise CAD representation of the object you scanned, ready to use in a fraction of the time it would take without these tools.

There are a number of features and parameters to look for in 3-D measuring tools:

Scan Accuracy–Range from .008-inch to .001-inch; accuracy is determined by comparing the variation between the actual point on the part versus the scanned point.
Scan Rate–Point-and-click (approximately point per second) to upward of 28,000 points per second.
Mobility–Solutions are offered for either fixed-station use or portability.
Size–The size of the components to be digitized may dictate the size of digitizer needed.
Functions to look for in scan-to-CAD software include:
Feature Recognition–Capability to reconstruct the part as a detailed CAD part object, allowing for manipulation through the CAD software tools.
Compatibility–Your CAD software and 3-D measuring tool need to be compatible with the scan-to-CAD software.

Rapid Prototyping

A key phase in the development process is validation of your design through testing. Doing so requires the production of prototypes to be used in evaluating the fit of the part as well as to benchmark and fine-tune the desired functional characteristics. The process is iterative, requiring multiple prototypes, with each implementing a design change or revision to further refine the design. Rapid prototyping enables you to produce prototypes directly from your CAD data, with lead times ranging from one to five days. Rapid prototyping machines build by joining layers of material into a desired shape. The costs for rapid prototypes are relatively low because there is no need to create tooling, and they provide one of the quickest approaches to building prototypes, thereby maximizing time usage.

SEMA News-May 2009-Research

Reverse engineering—This ’32 Ford coupe is captured in 3-D using a 3-D Laser Scanner and Point Cloud software.
Courtesy Konica Minolta

What to look for:

Machine Type–Stereolithography, selective laser sintering, fused deposition modeling, laminated object manufacturing and 3-D printing.
Material–Material selection is dictated by the machine, which includes photopolymer, polyamide material, epoxy-type resin and ABS plastic. Some are better used in form and fit evaluations, while others are strong enough to use in functional testing.
Size Capacity–Build envelopes vary. Packaged software may allow for splitting larger parts into smaller pieces that may be built by the machine.
Layer Thickness–Ranges from .004-inch to .0013-inch.

SEMA currently offers rapid prototyping as an extension of the Technology Transfer program to help introduce the technology’s benefits to its members.

CAM

If your company uses computer numeric control (CNC) machines as part of your manufacturing process, then you may also want to take a look at CAM software options. CNC machines offer repeatable accuracy and efficiency in manufacturing. CAM software analyzes the various part features of your design, identifying machinable surfaces and detecting the best path to take and then creating the program for all types of numerical control machines, including milling, turning, mold and die, multi-axis and more.

While most SEMA members say that they are using CAD, newer tools are available that utilize the drawings and turn traditional manufacturing into a high-tech and money-saving process. These new computer tools make the most of technology.

Fri, 05/01/2009 - 14:55

SEMA News - May 2009

RESEARCH

By Oscar Muñoz

Computer Tools for Design

Making the Most of Technology

SEMA News-May 2009-Research 

CAD systems allow your company to make designs such as this and enable you to take advantage of technologies geared toward bringing your product to market faster, better and at a lower cost.

 
In a recent SEMA survey of specialty-equipment manufacturers, 83% of respondents said that they use computer-aided design (CAD) software as part of their new-product design process. It is an indication that our industry is embracing CAD as it has become more attainable and easy to use due in large part to the constant gains in processing power that today’s PCs provide.

The primary benefit of using CAD is the streamlining it creates for the development of new products, which can be coupled to third-party software tools that extend functionality beyond the basics of mechanical design. Reverse engineering, rapid prototyping and computer-aided manufacturing (CAM) are just a few examples of tools that work within CAD applications to maximize development for any manufacturing organization. We’d like to offer a glimpse at the technologies that are available and can be easily integrated with your CAD software to reduce your research and development and enhance some of your consumer-outreach operations.

MCAD Application

Mechanical computer-aided design/drafting (MCAD) software provides engineers with an array of features that allows them to more easily develop products. At the core of each application is a modeling feature that lets the user create sketches from which a 3-D component will be produced. Generally speaking, most designs begin from a 2-D sketch and progress from there into a final design once depth and details are worked in. The process can be time-consuming, particularly if the model carries high levels of detail. However, the software provides a rich set of tools and wizards that make the process progress smoothly. Fillets, cuts, extrusions, edges, drafts, shells, patterns and ribs are all preset functions available through a button or wizard that simplifies the process. If you’re not sure, a simple click on a pull-down menu will get you started on a tutorial for further guidance.

SEMA News-May 2009-Research  

CAD software helps your company with more than design and manufacturing. In a matter of minutes you can take a CAD drawing (p. 44) and create a photorealistic rendering (above) to increase the appeal of proposals, marketing brochures or presentations—extending its reach into more aspects of your business operations than just R&D.

As you move from part design to assembly modeling, you begin to position and define the relationships between the parts of the assembly. Parts that have a set of motion relations with respect to each component (i.e. sprockets, pulleys, linkages) would be linked with each other so that clicking and dragging any part of the moving set would simulate the corresponding motion among involved parts. This helps identify interference with nearby parts or possible collisions as well as observe and measure relative velocities and accelerations that can be used to further analyze the forces in the system and better engineer the product. Other features of note are bill-of-materials generation and photorealistic rendering. Both not only facilitate communications between the engineer and other departments in the organization, but also provide content that can be used in the development of proposals, presentations and virtual demonstrations of the product, which help reduce the additional costs of having other departments create the material from scratch.

If you’re interested in evaluating a CAD software package, several companies offer free trial versions, including AutoCAD, Rhino3D and SolidWorks.

SEMA News-May 2009-Research

 

A rapid prototyping machine can take your CAD design and provide you with a prototype within one to two days. SEMA uses this model from Dimension Printing to provide rapid prototyping service to its members.
Courtesy Dimension Printing

 

Reverse Engineering

Reverse engineering tools are aids to designing products that will be installed on a vehicle. In order for the parts to fit and function as designed, accurate measurements need to be taken. A two-part combination of tools is needed to easily and effectively capture this data and import it into your CAD software. A 3-D measurement tool is used to capture the data from either a part that has been fabricated without CAD or an existing part taken from a vehicle. There are two main types of tools: a contact type, where the machine needs to physically touch the target object being digitized, and a non-contact type, such as a laser scanner or camera that projects light on the target object and captures the reflected light. In either case, the machine establishes a reference frame and sends point coordinates to a connected laptop. Captured data can then be fed to the second part of the tool combination, a specialized software application that will place the dots into a virtual 3-D space and reconstruct the object, identifying key features and constructing them as you would in your CAD software. The result is a precise CAD representation of the object you scanned, ready to use in a fraction of the time it would take without these tools.

There are a number of features and parameters to look for in 3-D measuring tools:

Scan Accuracy–Range from .008-inch to .001-inch; accuracy is determined by comparing the variation between the actual point on the part versus the scanned point.
Scan Rate–Point-and-click (approximately point per second) to upward of 28,000 points per second.
Mobility–Solutions are offered for either fixed-station use or portability.
Size–The size of the components to be digitized may dictate the size of digitizer needed.
Functions to look for in scan-to-CAD software include:
Feature Recognition–Capability to reconstruct the part as a detailed CAD part object, allowing for manipulation through the CAD software tools.
Compatibility–Your CAD software and 3-D measuring tool need to be compatible with the scan-to-CAD software.

Rapid Prototyping

A key phase in the development process is validation of your design through testing. Doing so requires the production of prototypes to be used in evaluating the fit of the part as well as to benchmark and fine-tune the desired functional characteristics. The process is iterative, requiring multiple prototypes, with each implementing a design change or revision to further refine the design. Rapid prototyping enables you to produce prototypes directly from your CAD data, with lead times ranging from one to five days. Rapid prototyping machines build by joining layers of material into a desired shape. The costs for rapid prototypes are relatively low because there is no need to create tooling, and they provide one of the quickest approaches to building prototypes, thereby maximizing time usage.

SEMA News-May 2009-Research

Reverse engineering—This ’32 Ford coupe is captured in 3-D using a 3-D Laser Scanner and Point Cloud software.
Courtesy Konica Minolta

What to look for:

Machine Type–Stereolithography, selective laser sintering, fused deposition modeling, laminated object manufacturing and 3-D printing.
Material–Material selection is dictated by the machine, which includes photopolymer, polyamide material, epoxy-type resin and ABS plastic. Some are better used in form and fit evaluations, while others are strong enough to use in functional testing.
Size Capacity–Build envelopes vary. Packaged software may allow for splitting larger parts into smaller pieces that may be built by the machine.
Layer Thickness–Ranges from .004-inch to .0013-inch.

SEMA currently offers rapid prototyping as an extension of the Technology Transfer program to help introduce the technology’s benefits to its members.

CAM

If your company uses computer numeric control (CNC) machines as part of your manufacturing process, then you may also want to take a look at CAM software options. CNC machines offer repeatable accuracy and efficiency in manufacturing. CAM software analyzes the various part features of your design, identifying machinable surfaces and detecting the best path to take and then creating the program for all types of numerical control machines, including milling, turning, mold and die, multi-axis and more.

While most SEMA members say that they are using CAD, newer tools are available that utilize the drawings and turn traditional manufacturing into a high-tech and money-saving process. These new computer tools make the most of technology.