New Products and Technology

New Products From Permatex, Oracle Lighting, Anvil Off-Road and More

By Fredy Ramirez

SEMA eNews highlights products from member-companies each week. This week's submissions are listed below.

The companies included with the SEMA Data Co-op (SDC) logo are also members of the SDC, the definitive, industry-owned and -operated centralized data repository. Learn more about the SDC at

Submit new-product press releases for consideration to

Oracle Lighting ColorSHIFT DRL

Oracle Lighting

Oracle Lighting announces the release of the ColorSHIFT DRL for the ‘17–‘20 Tesla Model 3. The modules use LEDs and other components. The boards are designed to be compatible with the factory system and should not cause any fault codes to appear when installed.

The kit includes the complete set of ColorSHIFT replacement DRLS, choice of ColorSHIFT controller and installation wiring kit.

800 407-5776
PN 1286

Rekudo Front Sway Bar

Rekudo Front Sway Bar

REKUDO announces the release of its front sway bar for the ‘70–‘81 GM F-body. The bar is designed to reduce body roll and stiffen the front suspension. The polyurethane frame and end link bushings are engineered for durability and to allow the bar to come into action immediately by eliminating compression. REKUDO includes Zerk fittings in the bushing frame brackets. Installation hardware is included.

PN RK500-02

H&R OE Sport Springs for BMW X3 M & X3 M Competition

H&R OE Sport Springs

H&R announces the launch of its OE Sport Springs for the BMW X3 M & X3 M Competition. The springs are designed to lower approximately 1.2 in. in the front and 1 in. in the rear.

The springs are also manufactured to improve handling and balance by lowering the vehicle’s center of gravity. H&R OE Sport Springs are 100% made in Germany and come with a limited lifetime warranty.

PN 28650-1

Flowtech LS Swap Exhaust Manifolds

FlowtechFlowtech's introduces its cast-iron exhaust manifolds. The manifold is designed to hug close to the engine block to allow them to fit into a wide variety of replacement and engine-swap applications. Their cast-iron construction is engineered to provide durability. The design is manufactured to allow for routing exhaust tubing close to frame and/or floor pan. The cast-iron manifolds are constructed to withstand weathering.

PN 11730FLT

Hooker BlackHeart Transmission Crossmembers

Hooker BlackheartHooker Blackheart's announces the release of its transmission crossmember for GEN III Hemi Swaps for the Mopar B-Body. The crossmember is constructed to allow the installation of A727 3-speed, NAG1 5-Speed, and 8HP70 8-speed automatic transmissions. The crossmembers are designed to use GM-style transmission mounts for its compact design that allows for better ground clearance than the OEM crossmember.


Hooker BlackHeart Long Tube Headers

Long Tube HeadersHooker BlackHeart has released its long-tube headers for the ‘66–’72 Mopar B-body Gen III Hemi.  The headers are engineered to allow use of popular transmissions with either left- or right-hand starters and can clear the factory power steering box with no modifications. Installing a low-mount A/C compressor will require the use of a VVT (variable valve timing) front drive system (2009-and-up VVT accessory drive front cover). The headers are designed to provide the most ground clearance possible and clear the torsion bar front suspension.

PN BH2358

MAHLE Motorsports PowerPak Plus Piston Kit

MAHLEMAHLE Motorsports announces the introduction of its Small-Block Chevy 305ci Flat Top PowerPak Plus Piston Kit. The kit is 4032 aluminum forged with asymmetrical valve pockets. Developed for a 3.480 stroke and 5.700 connecting rod, this kit is available to handle a range of compression ratios (58cc, 64cc or 70cc). The gas-ported version of this kit is also available.

PN Vary

Anvil Off-Road 3,500- & 4,500-Lb. Winch

Anvil Off-RoadAnvil Off-Road has released its 12-volt 3,500-lb. and 4,500-lb. winch for use on ATVs & UTVs. The winch is powered by a 2hp 12-volt permanent magnet motor. Featuring a 5mm x 32-ft. synthetic rope and aluminum Hawse fairlead, each kit includes the winch, fairlead, mounting plate, solenoid, handlebar switch, wireless remote, wire and hardware.

PN 3500 lbs. winch #3510AOR, 4500 lbs. winch #4511AOR

Anvil Off-Road 17,000-lb. Winch


Anvil Off-RoadAnvil Off-Road introduces its 17,000-lb. electric winch for use on 1-ton trucks as well as equipment trailers. The winch features a 7hp 12-volt motor and 3-stage planetary gear for 17,000 lbs. of pulling capacity (single line). The winches are available with a metal cable and 4-way roller fairlead and include a wireless remote control when situations make it difficult to reach the wired switch. Anvil's winch kits include the winch, fairlead, solenoid, wired switch, wireless remote, wire and hardware.

PN 17001AOR

Permatex Ultra Red Gasket Maker

PermatexPermatex has released its Ultra Red RTV Gasket Maker. It is designed to meet the needs of high-temperature repairs. The gasket maker is manufactured to be sensor-safe, low-odor, non-corrosive, and to meet performance specs of OE silicone gaskets. The formula is engineered to be resistant to high temperature and high adhesion while also remaining resistant to oils and common shop fluids. The gasket maker is constructed to perform at temperatures of up to 650°F (343°C).

PN 81630

Permatex The Right Stuff Red 90 Min Gasket Maker

PermatexPermatex launches its The Right Stuff Red 90 Minute RTV Gasket Maker. The gasket maker is designed to be the only high-temperature gasket maker in a tube that can quickly return a vehicle to service in 90 minutes while maintaining reliable and long-lasting seals. It is constructed to perform with temperatures of up to 650°F(343°C).

PN 34628