New Products and Technology

New Products From Aeromotive, PFC Brakes, Meguiar’s and More


By Fredy Ramirez

SEMA eNews highlights products from member-companies each week. This week's submissions are listed below.

The companies included with the SEMA Data Co-op (SDC) logo are also members of the SDC, the definitive, industry-owned and -operated centralized data repository. Learn more about the SDC at

Submit new-product press releases for consideration to

Aeromotive Fuel Pump Modules

Aeromotive introduces its direct drop-in fuel pump modules for ’11–’17 Ford Mustangs, excluding GT500 models. Phantom Series fuel pump modules are designed to be compatible with factory plastic fuel tanks; are available in single, dual and triple fuel pump configurations; and come preassembled. Available configurations include a single 450-lph pump engineered to support up to 700 hp; dual 340-lph pumps manufactured to support up to 1,295 hp; dual 450-lph pumps constructed support up to 1,500 hp; and triple 450-lph pumps designed to support up to 2,300 hp. Each configuration is also offered as a complete kit, including a fuel filter, a fuel pressure gauge and the recommended fuel pressure regulator based on flow rate. Kits do not include plumbing or electrical components to complete the installation.

PN: Vary


Meguiar’s Hybrid Ceramic Quik Clay Kit

Meguiar’s announces the launch of its Hybrid Ceramic Quik Clay Kit. The kit is designed to remove contaminants and get a smooth as glass surfaces. The kit includes Meguiar’s Synthetic Clay Pad, Meguiar’s Hybrid Ceramic Detailer and a Meguiar’s Supreme Shine Microfiber Towel. The soft foam applicator is treated with synthetic “clay”, a fine-tuned polymer technology engineered to remove bonded contaminants without hazing paint or marring the finish.

PN: G200200


PFC Brakes

PFC Brakes announces their line of Dyno-Bedded CarbonMetallic pads and ZERO FAILURES discs. The pads and discs are engineered to improve track time and increase the life of the pads and discs. These Dyno-Bedded parts will be available for the following markets in both PFC as well as competitors caliper pad shapes:

Asphalt tracks: Trans Am/TA2/Super Late-Model/NASCAR Late-Model Stock/Tour Modified
Dirt Tracks; Open Wheel Modifieds/Late-Model.

PN: Vary

PFC Brakes 

MAHLE Motorsport Forged PowerPak Piston Kit

MAHLE Motorsport introduces Forged PowerPak Piston Kit for LT-based direct-injected EcoTec3 5.3L engine. The pistons are dual coated with phosphate and MAHLE’s GRAFAL skirt coating manufactured for reduced drag, wear and noise, and hard anodized top ring grooves for durability and to protect against micro-welding. 1.0, 1.0, 2.0mm HV385 coated steel rings are also included. 

PN: Vary

MAHLE Motorsport

Hooker BlackHeart Transmission Crossmembers & Adapter Brackets

Hooker BlackHeart announces the release of its transmission crossmember. The crossmember is designed to allow the use of several different transmissions and uses a mounting bracket for each type of transmission. The design is engineered to allow future transmission changes by swapping out only the transmission mounting bracket instead of replacing the whole crossmember. Hooker BlackHeart crossmember brackets are engineered to allow the attachment of 8HP70, NAG1, TR6060, 545RFE/46RE, or A727 transmissions to your Gen III Hemi.

PN: BHS525

Hooker BlackHeart

Hooker BlackHeart Gen III Hemi Mid-Length D100/D150 Swap Headers

Hooker BlackHeart releases its mid-length swap headers for Gen-III Hemi D100 and D150. The headers are a part of a swap system engineered to provide component clearances, improved drivetrain geometry and clearance for a 3-in. exhaust system. These mid-length swap headers are made from 304 stainless steel.

PN: BH2355

Hooker BlackHeart

Go Rhino Convertible Rack

Go Rhino introduces its SRM400 convertible rack. The rack features a basket styling with removable front and rear plates for long loads, mounting lights and more. With a full 50-in. width, choose from 48-in., 58-in. and 68-in. lengths with crossbar U-bolt kit included. The front and rear fairings can be removed to accommodate multiple different light configurations (up to a 40-in. LED light bar). With fairings removed, the rack can be used to transport long, larger items such as kayaks and paddle boards for the weekend, or even lumber and conduit. Aluminum slotted crossbars allow for tools and attachments to be mounted inside the rack.

PN: 5934048T

Go Rhino Convertible Rack