Tue, 09/01/2009 - 17:21

SEMA News - September 2009



By Steve McDonald

LEGISLATIVE AND TECHNICAL AFFAIRS

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER 
 

Law and Order is an update of some of the most recent federal and state legislative and regulatory issues that could potentially impact the automotive specialty-equipment industry. These include issues affecting small-business owners and their employees.

California

Legislative Automotive Study Group: California Assemblymember Ted Gaines has formed an informal California Legislative Automotive Study Group, aimed at protecting and raising awareness of the “state’s automotive industry and the jobs it creates.” Assemblymember Felipe Fuentes will co-chair the group. The group plans to look into ways to “explore new environmentally friendly technologies and innovations” as well as promoting the off-road and auto enthusiast markets, which Gaines says accounts for 200,000 jobs in California. SEMA is contacting group members to offer its assistance and support.

Greenhouse Gases: The U.S. Environmental Protection Agency (EPA) announced that it will grant a waiver to California to allow the state to regulate greenhouse gas emissions from cars and trucks. Until at least 2016, however, California will pursue the national approach adopted by the Obama Administration. The decision ends a seven-year battle by California to establish standards to limit emissions of carbon dioxide and other greenhouse gases. In 2007, the Bush Administration blocked implementation of the California CO2 rule, which had been adopted by 13 other states. Since the federal standards will not begin until 2012, the waiver technically allows California and other states to enforce their own standards. More importantly, the waiver will permit California to pursue stricter standards after 2016.

Tire Fuel Efficiency: California has issued a regulatory proposal to establish a tire fuel-efficiency rating system. The regulation is based on a 2003 California law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. California regulators are proposing a program that would assign a “fuel-efficient tire” ranking to the top 15% of tires with the lowest rolling resistance within their size and load class. All other tested tires would be ranked as “tires that are not fuel efficient.” If enacted, the testing program would take effect in mid 2011. Manufacturers would also be required to report other tire information, such as load index, federal Uniform Tire Quality Grading System rating and speed rating.

Connecticut

Vehicle Noise: SEMA helped defeat legislation that would require motor vehicles and devices to be operated, constructed and adjusted to prevent unnecessary or unusual noise. The bill did not define what constituted unnecessary or unusual noise. SEMA also persuaded lawmakers not to pass legislation that sought to provide an incentive to localities to increase the number of citations issued for violation of vehicle noise regulations.

North Carolina

Scrappage: SEMA persuaded North Carolina legislators not to consider legislation that would have implemented a state vehicle scrappage program for passenger vehicles that are at least 14 years old. Participants would have received around $1,000 to $1,500 to scrap their cars and purchase current-year vehicles under 10,000 pounds or from the previous three model years. All trade-in vehicles could have been destroyed, regardless of their historical value or collector interest. Had this effort been successful, hobbyists could have been denied the availability of vintage cars and parts for restoration projects.

Oregon

Aftermarket Parts: The Oregon House and Senate approved an alternative to legislation that originally sought to prohibit the sale and distribution of aftermarket motor vehicle parts if alternatives are available that “decrease greenhouse gas emissions from motor vehicles.” Under the alternative, negotiated between SEMA and the Oregon Department of Environmental Quality, the bill would only give the department authority to adopt the present California certification process for aftermarket emissions-related parts, allowing parts manufacturers to meet one uniform standard rather than a patchwork of multiple state standards. The amended legislation will also incorporate a California law that requires state regulators to develop a tire fuel-efficiency program for passenger car and light-truck replacement tires. As in California, Oregon includes a SEMA-drafted provision to exempt limited-production tires (15,000 or less annually), deep-tread snow tires, limited-use spares, motorcycle tires and tires manufactured for use on off-road vehicles. The bill will now be transmitted to the governor for his signature and enactment into law.

Tennessee

Antique Vehicles: Legislation to amend the state’s current law defining antique motor vehicles to also permit use of these vehicles for “selling, testing the operation of or obtaining repairs” was signed into law by Governor Phil Bredesen. The bill had originally contained a SEMA-supported provision to allow use for everyday general transportation. In addition to the new allowances, the Tennessee law continues to permit use of antique vehicles for club activities, exhibits, tours and for general transportation on Saturday and Sunday.

Federal Update

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER

Health Care Reform: Congress is working this summer to complete House and Senate bills to overhaul how Americans gain access to affordable health care insurance. The ultimate goal for congressional Democrats is to finalize a single bill this fall to be sent to President Obama. Given the complexity of the issue and its financial ramifications, a number of reform measures have been proposed and debated. Topics that are being simultaneously addressed include providing expanded coverage, cost containment, improved quality, simplified administration and equitable financing. SEMA continues to support cost-containment measures, such as allowing small businesses to gain access to national or large state coverage pools. SEMA’s advocacy efforts are coordinated with the Small Business Coalition for Affordable Healthcare and the National Federation of Independent Businesses.

Greenhouse Gases: The U.S. House of Representatives passed landmark legislation to establish national limits on greenhouse gases and an emissions credit trading system. The bill’s intent is to gradually switch the nation from fossil fuels to sources of “clean” power, such as wind and solar energy. The legislation would require a 17% reduction in carbon dioxide (CO2) emissions by 2020 and 80% by 2050, based on 2005 levels. The primary targets are large stationary source emitters such as powerplants, factories and refineries. The bill would establish a market for issuing CO2 permits that could then be bought and sold as a mechanism for regulating emissions limits. This approach has been adopted in Europe and is similar to the EPA’s acid rain program, which limits sulfur dioxide from coal-fired powerplants and other sources. Auto tailpipe emissions would be regulated under a previously announced Obama Administration program to link CO2 emissions to the CAFE standards (since CO2 is released in proportion to the amount of carbon-based fuel that is burned.) This approach is supported by SEMA and the automakers, since it has the advantage of creating a single national CO2 standard. A Congressional study projects that the House bill will raise average household energy prices from $80 to $111. Opponents believe that the estimates are too low and that American jobs will migrate to countries that do not have equivalent climate regulations. The U.S. Senate is expected to consider its version of the legislation this fall. President Obama has made passage of the bill a top domestic priority.

Tire Fuel Efficiency: The National Highway Traffic Safety Administration (NHTSA) has issued a proposal to establish a tire fuel-efficiency rating system. The plans stem from a 2007 federal energy law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. Under the federal program, tire manufacturers would be required to label their replacement tires for fuel efficiency, safety and durability based on performance tests established by NHTSA. The label would display a scale ranging from 0 to 100, with 100 being the best rating. NHTSA must issue a final rule by the end of 2009.

Light Truck Bumper Standard: NHTSA is seeking public comment on whether to apply the bumper standard to light trucks, vans and SUVs, since they now represent a large percentage of the nation’s car fleet. The bumper standard has only applied to passenger cars since it was implemented in 1972. The standard’s performance requirements are intended to prevent damage to the car body and safety-related equipment at 2½ mph across the full width of the front and rear bumper and 1½ mph on the corners.

Daytime Running Lamps: NHTSA denied a longstanding petition by General Motors that the agency mandate installation of daytime running lamps (DRLs) on all new light-duty vehicles. NHTSA’s decision was based on study results that it found did not provide substantial evidence of an overall safety benefit, although the lighting equipment may be beneficial under certain scenarios. NHTSA will continue to maintain a neutral position on the technology and allow manufacturers to make individual decisions on whether to voluntarily install DRLs. The DRLs must meet performance criteria issued by NHTSA, which are meant to address potential glare.

Aerosol Paints: The EPA has added 128 substances to the list of chemicals sometimes found in aerosol paints that emit volatile organic compounds (VOCs). The primary substances include formaldehyde, ethanol, benzene, propane and vinyl chloride. VOCs react with nitrogen oxides in the presence of sunlight to form ground-level ozone. Spray paint manufacturers must now determine whether their products contain the substances and still comply with VOC emissions limits that took effect in 2009 for spray paints, primers and clear coatings. The EPA rule is similar to a California standard and applies to manufacturers and distributors of aerosol products that are used for both industrial applications and by do-it-yourselfers. The EPA believes that most producers already comply with the rule. Manufacturers that make limited quantities of aerosol spray paints containing VOCs (less than 7,500 kilograms/8.3 tons) on an annual basis are exempt from the regulation.

Tue, 09/01/2009 - 17:21

SEMA News - September 2009



By Steve McDonald

LEGISLATIVE AND TECHNICAL AFFAIRS

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER 
 

Law and Order is an update of some of the most recent federal and state legislative and regulatory issues that could potentially impact the automotive specialty-equipment industry. These include issues affecting small-business owners and their employees.

California

Legislative Automotive Study Group: California Assemblymember Ted Gaines has formed an informal California Legislative Automotive Study Group, aimed at protecting and raising awareness of the “state’s automotive industry and the jobs it creates.” Assemblymember Felipe Fuentes will co-chair the group. The group plans to look into ways to “explore new environmentally friendly technologies and innovations” as well as promoting the off-road and auto enthusiast markets, which Gaines says accounts for 200,000 jobs in California. SEMA is contacting group members to offer its assistance and support.

Greenhouse Gases: The U.S. Environmental Protection Agency (EPA) announced that it will grant a waiver to California to allow the state to regulate greenhouse gas emissions from cars and trucks. Until at least 2016, however, California will pursue the national approach adopted by the Obama Administration. The decision ends a seven-year battle by California to establish standards to limit emissions of carbon dioxide and other greenhouse gases. In 2007, the Bush Administration blocked implementation of the California CO2 rule, which had been adopted by 13 other states. Since the federal standards will not begin until 2012, the waiver technically allows California and other states to enforce their own standards. More importantly, the waiver will permit California to pursue stricter standards after 2016.

Tire Fuel Efficiency: California has issued a regulatory proposal to establish a tire fuel-efficiency rating system. The regulation is based on a 2003 California law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. California regulators are proposing a program that would assign a “fuel-efficient tire” ranking to the top 15% of tires with the lowest rolling resistance within their size and load class. All other tested tires would be ranked as “tires that are not fuel efficient.” If enacted, the testing program would take effect in mid 2011. Manufacturers would also be required to report other tire information, such as load index, federal Uniform Tire Quality Grading System rating and speed rating.

Connecticut

Vehicle Noise: SEMA helped defeat legislation that would require motor vehicles and devices to be operated, constructed and adjusted to prevent unnecessary or unusual noise. The bill did not define what constituted unnecessary or unusual noise. SEMA also persuaded lawmakers not to pass legislation that sought to provide an incentive to localities to increase the number of citations issued for violation of vehicle noise regulations.

North Carolina

Scrappage: SEMA persuaded North Carolina legislators not to consider legislation that would have implemented a state vehicle scrappage program for passenger vehicles that are at least 14 years old. Participants would have received around $1,000 to $1,500 to scrap their cars and purchase current-year vehicles under 10,000 pounds or from the previous three model years. All trade-in vehicles could have been destroyed, regardless of their historical value or collector interest. Had this effort been successful, hobbyists could have been denied the availability of vintage cars and parts for restoration projects.

Oregon

Aftermarket Parts: The Oregon House and Senate approved an alternative to legislation that originally sought to prohibit the sale and distribution of aftermarket motor vehicle parts if alternatives are available that “decrease greenhouse gas emissions from motor vehicles.” Under the alternative, negotiated between SEMA and the Oregon Department of Environmental Quality, the bill would only give the department authority to adopt the present California certification process for aftermarket emissions-related parts, allowing parts manufacturers to meet one uniform standard rather than a patchwork of multiple state standards. The amended legislation will also incorporate a California law that requires state regulators to develop a tire fuel-efficiency program for passenger car and light-truck replacement tires. As in California, Oregon includes a SEMA-drafted provision to exempt limited-production tires (15,000 or less annually), deep-tread snow tires, limited-use spares, motorcycle tires and tires manufactured for use on off-road vehicles. The bill will now be transmitted to the governor for his signature and enactment into law.

Tennessee

Antique Vehicles: Legislation to amend the state’s current law defining antique motor vehicles to also permit use of these vehicles for “selling, testing the operation of or obtaining repairs” was signed into law by Governor Phil Bredesen. The bill had originally contained a SEMA-supported provision to allow use for everyday general transportation. In addition to the new allowances, the Tennessee law continues to permit use of antique vehicles for club activities, exhibits, tours and for general transportation on Saturday and Sunday.

Federal Update

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER

Health Care Reform: Congress is working this summer to complete House and Senate bills to overhaul how Americans gain access to affordable health care insurance. The ultimate goal for congressional Democrats is to finalize a single bill this fall to be sent to President Obama. Given the complexity of the issue and its financial ramifications, a number of reform measures have been proposed and debated. Topics that are being simultaneously addressed include providing expanded coverage, cost containment, improved quality, simplified administration and equitable financing. SEMA continues to support cost-containment measures, such as allowing small businesses to gain access to national or large state coverage pools. SEMA’s advocacy efforts are coordinated with the Small Business Coalition for Affordable Healthcare and the National Federation of Independent Businesses.

Greenhouse Gases: The U.S. House of Representatives passed landmark legislation to establish national limits on greenhouse gases and an emissions credit trading system. The bill’s intent is to gradually switch the nation from fossil fuels to sources of “clean” power, such as wind and solar energy. The legislation would require a 17% reduction in carbon dioxide (CO2) emissions by 2020 and 80% by 2050, based on 2005 levels. The primary targets are large stationary source emitters such as powerplants, factories and refineries. The bill would establish a market for issuing CO2 permits that could then be bought and sold as a mechanism for regulating emissions limits. This approach has been adopted in Europe and is similar to the EPA’s acid rain program, which limits sulfur dioxide from coal-fired powerplants and other sources. Auto tailpipe emissions would be regulated under a previously announced Obama Administration program to link CO2 emissions to the CAFE standards (since CO2 is released in proportion to the amount of carbon-based fuel that is burned.) This approach is supported by SEMA and the automakers, since it has the advantage of creating a single national CO2 standard. A Congressional study projects that the House bill will raise average household energy prices from $80 to $111. Opponents believe that the estimates are too low and that American jobs will migrate to countries that do not have equivalent climate regulations. The U.S. Senate is expected to consider its version of the legislation this fall. President Obama has made passage of the bill a top domestic priority.

Tire Fuel Efficiency: The National Highway Traffic Safety Administration (NHTSA) has issued a proposal to establish a tire fuel-efficiency rating system. The plans stem from a 2007 federal energy law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. Under the federal program, tire manufacturers would be required to label their replacement tires for fuel efficiency, safety and durability based on performance tests established by NHTSA. The label would display a scale ranging from 0 to 100, with 100 being the best rating. NHTSA must issue a final rule by the end of 2009.

Light Truck Bumper Standard: NHTSA is seeking public comment on whether to apply the bumper standard to light trucks, vans and SUVs, since they now represent a large percentage of the nation’s car fleet. The bumper standard has only applied to passenger cars since it was implemented in 1972. The standard’s performance requirements are intended to prevent damage to the car body and safety-related equipment at 2½ mph across the full width of the front and rear bumper and 1½ mph on the corners.

Daytime Running Lamps: NHTSA denied a longstanding petition by General Motors that the agency mandate installation of daytime running lamps (DRLs) on all new light-duty vehicles. NHTSA’s decision was based on study results that it found did not provide substantial evidence of an overall safety benefit, although the lighting equipment may be beneficial under certain scenarios. NHTSA will continue to maintain a neutral position on the technology and allow manufacturers to make individual decisions on whether to voluntarily install DRLs. The DRLs must meet performance criteria issued by NHTSA, which are meant to address potential glare.

Aerosol Paints: The EPA has added 128 substances to the list of chemicals sometimes found in aerosol paints that emit volatile organic compounds (VOCs). The primary substances include formaldehyde, ethanol, benzene, propane and vinyl chloride. VOCs react with nitrogen oxides in the presence of sunlight to form ground-level ozone. Spray paint manufacturers must now determine whether their products contain the substances and still comply with VOC emissions limits that took effect in 2009 for spray paints, primers and clear coatings. The EPA rule is similar to a California standard and applies to manufacturers and distributors of aerosol products that are used for both industrial applications and by do-it-yourselfers. The EPA believes that most producers already comply with the rule. Manufacturers that make limited quantities of aerosol spray paints containing VOCs (less than 7,500 kilograms/8.3 tons) on an annual basis are exempt from the regulation.

Tue, 09/01/2009 - 17:21

SEMA News - September 2009



By Steve McDonald

LEGISLATIVE AND TECHNICAL AFFAIRS

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER 
 

Law and Order is an update of some of the most recent federal and state legislative and regulatory issues that could potentially impact the automotive specialty-equipment industry. These include issues affecting small-business owners and their employees.

California

Legislative Automotive Study Group: California Assemblymember Ted Gaines has formed an informal California Legislative Automotive Study Group, aimed at protecting and raising awareness of the “state’s automotive industry and the jobs it creates.” Assemblymember Felipe Fuentes will co-chair the group. The group plans to look into ways to “explore new environmentally friendly technologies and innovations” as well as promoting the off-road and auto enthusiast markets, which Gaines says accounts for 200,000 jobs in California. SEMA is contacting group members to offer its assistance and support.

Greenhouse Gases: The U.S. Environmental Protection Agency (EPA) announced that it will grant a waiver to California to allow the state to regulate greenhouse gas emissions from cars and trucks. Until at least 2016, however, California will pursue the national approach adopted by the Obama Administration. The decision ends a seven-year battle by California to establish standards to limit emissions of carbon dioxide and other greenhouse gases. In 2007, the Bush Administration blocked implementation of the California CO2 rule, which had been adopted by 13 other states. Since the federal standards will not begin until 2012, the waiver technically allows California and other states to enforce their own standards. More importantly, the waiver will permit California to pursue stricter standards after 2016.

Tire Fuel Efficiency: California has issued a regulatory proposal to establish a tire fuel-efficiency rating system. The regulation is based on a 2003 California law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. California regulators are proposing a program that would assign a “fuel-efficient tire” ranking to the top 15% of tires with the lowest rolling resistance within their size and load class. All other tested tires would be ranked as “tires that are not fuel efficient.” If enacted, the testing program would take effect in mid 2011. Manufacturers would also be required to report other tire information, such as load index, federal Uniform Tire Quality Grading System rating and speed rating.

Connecticut

Vehicle Noise: SEMA helped defeat legislation that would require motor vehicles and devices to be operated, constructed and adjusted to prevent unnecessary or unusual noise. The bill did not define what constituted unnecessary or unusual noise. SEMA also persuaded lawmakers not to pass legislation that sought to provide an incentive to localities to increase the number of citations issued for violation of vehicle noise regulations.

North Carolina

Scrappage: SEMA persuaded North Carolina legislators not to consider legislation that would have implemented a state vehicle scrappage program for passenger vehicles that are at least 14 years old. Participants would have received around $1,000 to $1,500 to scrap their cars and purchase current-year vehicles under 10,000 pounds or from the previous three model years. All trade-in vehicles could have been destroyed, regardless of their historical value or collector interest. Had this effort been successful, hobbyists could have been denied the availability of vintage cars and parts for restoration projects.

Oregon

Aftermarket Parts: The Oregon House and Senate approved an alternative to legislation that originally sought to prohibit the sale and distribution of aftermarket motor vehicle parts if alternatives are available that “decrease greenhouse gas emissions from motor vehicles.” Under the alternative, negotiated between SEMA and the Oregon Department of Environmental Quality, the bill would only give the department authority to adopt the present California certification process for aftermarket emissions-related parts, allowing parts manufacturers to meet one uniform standard rather than a patchwork of multiple state standards. The amended legislation will also incorporate a California law that requires state regulators to develop a tire fuel-efficiency program for passenger car and light-truck replacement tires. As in California, Oregon includes a SEMA-drafted provision to exempt limited-production tires (15,000 or less annually), deep-tread snow tires, limited-use spares, motorcycle tires and tires manufactured for use on off-road vehicles. The bill will now be transmitted to the governor for his signature and enactment into law.

Tennessee

Antique Vehicles: Legislation to amend the state’s current law defining antique motor vehicles to also permit use of these vehicles for “selling, testing the operation of or obtaining repairs” was signed into law by Governor Phil Bredesen. The bill had originally contained a SEMA-supported provision to allow use for everyday general transportation. In addition to the new allowances, the Tennessee law continues to permit use of antique vehicles for club activities, exhibits, tours and for general transportation on Saturday and Sunday.

Federal Update

SEMA NEWS-SEPTEMBER 2009-LAW AND ORDER

Health Care Reform: Congress is working this summer to complete House and Senate bills to overhaul how Americans gain access to affordable health care insurance. The ultimate goal for congressional Democrats is to finalize a single bill this fall to be sent to President Obama. Given the complexity of the issue and its financial ramifications, a number of reform measures have been proposed and debated. Topics that are being simultaneously addressed include providing expanded coverage, cost containment, improved quality, simplified administration and equitable financing. SEMA continues to support cost-containment measures, such as allowing small businesses to gain access to national or large state coverage pools. SEMA’s advocacy efforts are coordinated with the Small Business Coalition for Affordable Healthcare and the National Federation of Independent Businesses.

Greenhouse Gases: The U.S. House of Representatives passed landmark legislation to establish national limits on greenhouse gases and an emissions credit trading system. The bill’s intent is to gradually switch the nation from fossil fuels to sources of “clean” power, such as wind and solar energy. The legislation would require a 17% reduction in carbon dioxide (CO2) emissions by 2020 and 80% by 2050, based on 2005 levels. The primary targets are large stationary source emitters such as powerplants, factories and refineries. The bill would establish a market for issuing CO2 permits that could then be bought and sold as a mechanism for regulating emissions limits. This approach has been adopted in Europe and is similar to the EPA’s acid rain program, which limits sulfur dioxide from coal-fired powerplants and other sources. Auto tailpipe emissions would be regulated under a previously announced Obama Administration program to link CO2 emissions to the CAFE standards (since CO2 is released in proportion to the amount of carbon-based fuel that is burned.) This approach is supported by SEMA and the automakers, since it has the advantage of creating a single national CO2 standard. A Congressional study projects that the House bill will raise average household energy prices from $80 to $111. Opponents believe that the estimates are too low and that American jobs will migrate to countries that do not have equivalent climate regulations. The U.S. Senate is expected to consider its version of the legislation this fall. President Obama has made passage of the bill a top domestic priority.

Tire Fuel Efficiency: The National Highway Traffic Safety Administration (NHTSA) has issued a proposal to establish a tire fuel-efficiency rating system. The plans stem from a 2007 federal energy law mandating a program to provide consumers with information about the fuel efficiency of replacement tires. The law contains a SEMA provision exempting manufacturers of tires that have the same SKU, plant and year and have been produced or imported in annual units of less than 15,000. Under the federal program, tire manufacturers would be required to label their replacement tires for fuel efficiency, safety and durability based on performance tests established by NHTSA. The label would display a scale ranging from 0 to 100, with 100 being the best rating. NHTSA must issue a final rule by the end of 2009.

Light Truck Bumper Standard: NHTSA is seeking public comment on whether to apply the bumper standard to light trucks, vans and SUVs, since they now represent a large percentage of the nation’s car fleet. The bumper standard has only applied to passenger cars since it was implemented in 1972. The standard’s performance requirements are intended to prevent damage to the car body and safety-related equipment at 2½ mph across the full width of the front and rear bumper and 1½ mph on the corners.

Daytime Running Lamps: NHTSA denied a longstanding petition by General Motors that the agency mandate installation of daytime running lamps (DRLs) on all new light-duty vehicles. NHTSA’s decision was based on study results that it found did not provide substantial evidence of an overall safety benefit, although the lighting equipment may be beneficial under certain scenarios. NHTSA will continue to maintain a neutral position on the technology and allow manufacturers to make individual decisions on whether to voluntarily install DRLs. The DRLs must meet performance criteria issued by NHTSA, which are meant to address potential glare.

Aerosol Paints: The EPA has added 128 substances to the list of chemicals sometimes found in aerosol paints that emit volatile organic compounds (VOCs). The primary substances include formaldehyde, ethanol, benzene, propane and vinyl chloride. VOCs react with nitrogen oxides in the presence of sunlight to form ground-level ozone. Spray paint manufacturers must now determine whether their products contain the substances and still comply with VOC emissions limits that took effect in 2009 for spray paints, primers and clear coatings. The EPA rule is similar to a California standard and applies to manufacturers and distributors of aerosol products that are used for both industrial applications and by do-it-yourselfers. The EPA believes that most producers already comply with the rule. Manufacturers that make limited quantities of aerosol spray paints containing VOCs (less than 7,500 kilograms/8.3 tons) on an annual basis are exempt from the regulation.

Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Advantage Truck Accessories Inc.
2009 Dodge RamBox Tonneau Cover Applications

Advantage Truck Accessories announced tonneau cover applications for the new 2009 Dodge RamBox pickup models. The unique, segment-exclusive cargo management system that features lengthwise storage bins on the outside of the cargo area maintains functionality with the tonneau covers installed. Advantage folding cover models, both the soft TorzaTop and the solid HardHat, may be used in their partial and fully closed positions. Shown is the Advantage TorzaTop installed on the new Dodge Crew Cab with its unique RamBox side storage bins.

Advantage Truck Accessories Inc.
574/293-0979

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Automotive Performance Systems
You Can Do It! In a Job or Your Own
Business…Make Your Life a Success

Bill Neumann is the founder and CEO of Automotive Performance Systems and Neumann Distributing. You Can Do It! is the inspirational story of how Bill accomplished his goals and realized his dreams.

Automotive Performance Systems
805/388-7171

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Carpod
Carpod

Carpod is proud to introduce what the company claims is the most versatile hitch-mounted cargo carrier of its kind. The Carpod easily hitches to the back of a vehicle and features 22-inch sidewalls that can be folded up to keep cargo safe and contained during transport or folded down for ease of storage. Carpod accommodates cargo of up to 450 pounds and 13.25 cubic feet.

Carpod
818/395-8676

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

CarTech Auto Books & Manuals
How to Build Max-Performance Hemi Engines

How to Build Max-Performance Hemi Engines details how to extract more horsepower from second-generation Hemi engines. All of the block options are presented, including street versus race, new versus old and iron versus aluminum. Author Richard Nedbal explores major head types, rocker-arm systems, head machining and prep, valves, springs, seats, porting quench control and more. The book also examines in detail how to install and set up power adders such as nitrous oxide, superchargers and turbochargers.

CarTech Auto Books & Manuals
800/551-4754

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS Classic Industries
Newest Chevrolet/GMC Truck Catalog

Classic Industries’ newest catalog offers restoration and performance parts and accessories for all 1947-2008 Chevrolet and GMC truck models. At 900 pages, this full-color catalog is the most complete offering of new products for the truck owner and restorer. Notable items in this edition include interior components, upholstery, body components, apparel and accessories for the complete Chevrolet/GMC lifestyle.

Classic Industries
800/854-1280

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Emhart Teknologies
Professional Manual Rivet Tool Kit

Emhart Teknologies has just expanded its line of Pop Nut blind rivet nuts and tools with the addition of two new tool kits — featuring the PNT110 manual tool. The PNT110 is ergonomically designed to fit the user’s hand with contoured grips for comfort. The tool’s quick-change mandrel and nose piece design allow the user the flexibility of setting different size nuts.

Emhart Teknologies
203/924-9341

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Hurst Performance
Special Edition Hurst/Pontiacs

Hurst Performance Vehicles has announced that it has teamed up with newly appointed Hurst Director Emeritus “Doc” Watson to build two new special edition Hurst/Pontiacs—a 2010 Hurst/Pontiac H.O. version of the G8 and a G6 convertible. These numbered cars will feature Hurst’s iconic white/gold and black/gold colors along with forged-alloy Hurst wheels, an exclusive Hurst shifter, a supercharged engine, suspension mods and a specially trimmed interior.

Hurst Performance
949/261-5500

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

K&N Engineering
High-Flow Air Filter for the 2010 Ford Mustang GT 4.6L

According to the company, the K&N high-flow air filter for the 2010 Ford Mustang GT 4.6L V8 (part no. 33-2431) is designed to increase horsepower and acceleration while providing excellent filtration. The simple drop-in design makes it an easy performance Mustang add-on. K&N high-flow replacement filters are installed in minutes and comply with factory warranties. K&N filters can be easily cleaned with the Recharger maintenance kit and will last the life of the vehicle.

K&N Engineering
800/858-3333

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Speedway Motors
Stainless-Steel Batwings

According to Speedway Motors, what sets these batwings apart from the rest are the fully reinforced ½-inch-20 threaded bosses available for attaching a Panhard bar or shock mount. Investment cast from high-quality stainless steel, these beautiful batwings provide a strong and stylish means for attaching a four-bar suspension to your street rod’s front axle.

Speedway Motors
800/979-0122

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Meguiar’s
Ultimate Quick Wax

Meguiar’s unveiled its Ultimate Quik Detailer with hydrophobic polymer technology one year ago. Now the company has done it again with Meguiar’s Ultimate Quik Wax, featuring the same relentless water-beading properties with the added protection of a high-tech, easy-to-apply spray wax. According to Meguiar’s, when Quik Detailer becomes slow to wipe off, its time for a coat of Ultimate Quik Wax.

Meguiar’s
800/347-5700

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Metro Moulded Parts Inc.
Gold Series Vent Window Seals

Seal up the vent-wing window on 1963-64 Ford or Mercury fullsize cars with these premium-quality Gold Series vent window seals from Metro Moulded Rubber Parts. According to the company, these faithful reproductions are manufactured by Metro in the U.S. to the highest quality standards so that they will look correct and function exactly as designed by the OEM back in the day. Part number WR 3363 fits fullsize Ford and Mercury two-door and four-door sedans and station wagon models.

Metro Moulded Parts Inc.
800/878-2237

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Mr. Norm’s Garage
Mopar A-, B- and E-Body Rear
Suspensions

Mr. Norm’s Garage is proud to announce that it is now offering a comprehensive line of easy-to-install rear suspension systems for 1960s and 1970s Mopar A-, B- and E-body musclecars. Designed to fit 1967 thru 1976 A bodies, 1968 thru 1970 and 1971 thru 1974 B bodies and 1970 thru 1974 E bodies, these rear suspension systems by Mr. Norm’s Garage are available in both weld-in and bolt-in styles.

Mr. Norm’s Garage
727/869-9533

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

TMI Products
Mustang Center Consoles

TMI has just released a collection of beautifully crafted center consoles designed specifically for 1965 through 1973 Mustangs. According to TMI, these new centerpieces are a fashionable and extremely convenient addition to any Mustang interior. And you can dress it up or blend the console in by choosing from a wide selection of TMI’s stock style materials and colors or exclusive custom fabrics and tones. Quick and simple to install using hook-and-loop straps, TMI consoles fit directly over the transmission tunnel or OEM factory console.

TMI Products
800/624-7960

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Zex
Dodge Hemi Challenger Nitrous System

According to Zex, the new specially designed wet nitrous system delivers 75 to 175 additional horsepower to 2008-current Dodge Hemi Challengers. The Dodge 5.7L and 6.1L EFI Hemi engines are the perfect platform for nitrous injection upgrades. The Zex nitrous system for the new Dodge Hemi Challenger was extensively engineered for a simple plug-and-play installation and includes custom-designed brackets and a special fuel line adapter that helps finish the installation in only two to three hours.


Zex
888/817-1008
 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Wiley X
Wiley X Eyewear

According to Wiley X, one pair of high-performance Wiley X sunglasses is all any consumer needs, whether driving to work, cruising on the open water, working at a job site or factory or cutting loose on the weekend. The ballistic qualities and fashion-forward designs of Wiley X Eyewear provide comprehensive eye protection with stylish good looks.

Wiley X
800/776-7842

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Scosche
Kia Amanti Installation Kit

Scosche Industries is now shipping its new “custom kit, factory fit” Kia Amanti installation kit. The KA2095B is designed specifically for 2007 and up Kia Amanti vehicles. The KA2095B will accommodate either an ISO single-DIN mount with pocket or an ISO double-DIN mount.

Scosche
800/363-4490

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Omni Lubricants
Green Grease

Green Grease is now available in 55-gallon drums, 16-gallon kegs and 5-gallon pails. This multipurpose synthetic polymer grease is a professional-grade, high-performance grease developed for a multitude of applications. According to Omni, Green Grease really is waterproof, which is better than “water resistant.” The synthetic polymers in Green Grease create a seal that sticks to the metal, protecting bearings (U-joints, tie-rods, etc.) from contaminants, such as dust, sand, grit and dirt.

Omni Lubricants
877/GO-GREASE

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

PML
Big-Block Chevrolet Valve Covers

PML is now shipping tall big-block Chevrolet valve covers with classic Corvette script. According to the company, these tall valve covers feature strong sand-cast aluminum construction, raised Corvette script and fins, and cast-in baffles to prevent oil leaks. These new valve covers are taller than stock to accommodate roller rockers.

PML Inc.
310/671-4345

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Accel (A Div. of Prestolite Performance)
Extreme 9000 Ceramic Wire Kits

Accel now offers the cure for burned sparkplug-wire boots with Extreme 9000 ceramic wire kits. The 8mm ferro-spiral core wire now has ceramic boots that will withstand up to 2,000° F on the sparkplug end of the wires.

Accel
(A Div. of Prestolite Performance)
216/688-8300

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

RHS
Pro Elite SBC 23-Degree CNC-Ported Iron Cylinder Heads

According to RHS, its new SBC 228cc-runner heads provide maximum airflow for circle-track and drag-racing classes that require the use of cast-iron cylinder heads. The precision, accuracy and durability of the RHS heads are derived not only from the precision CNC-porting of the intake and exhaust runners, but the CNC-ported combustion chamber as well.

RHS
877/776-4323

 
Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Advantage Truck Accessories Inc.
2009 Dodge RamBox Tonneau Cover Applications

Advantage Truck Accessories announced tonneau cover applications for the new 2009 Dodge RamBox pickup models. The unique, segment-exclusive cargo management system that features lengthwise storage bins on the outside of the cargo area maintains functionality with the tonneau covers installed. Advantage folding cover models, both the soft TorzaTop and the solid HardHat, may be used in their partial and fully closed positions. Shown is the Advantage TorzaTop installed on the new Dodge Crew Cab with its unique RamBox side storage bins.

Advantage Truck Accessories Inc.
574/293-0979

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Automotive Performance Systems
You Can Do It! In a Job or Your Own
Business…Make Your Life a Success

Bill Neumann is the founder and CEO of Automotive Performance Systems and Neumann Distributing. You Can Do It! is the inspirational story of how Bill accomplished his goals and realized his dreams.

Automotive Performance Systems
805/388-7171

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Carpod
Carpod

Carpod is proud to introduce what the company claims is the most versatile hitch-mounted cargo carrier of its kind. The Carpod easily hitches to the back of a vehicle and features 22-inch sidewalls that can be folded up to keep cargo safe and contained during transport or folded down for ease of storage. Carpod accommodates cargo of up to 450 pounds and 13.25 cubic feet.

Carpod
818/395-8676

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

CarTech Auto Books & Manuals
How to Build Max-Performance Hemi Engines

How to Build Max-Performance Hemi Engines details how to extract more horsepower from second-generation Hemi engines. All of the block options are presented, including street versus race, new versus old and iron versus aluminum. Author Richard Nedbal explores major head types, rocker-arm systems, head machining and prep, valves, springs, seats, porting quench control and more. The book also examines in detail how to install and set up power adders such as nitrous oxide, superchargers and turbochargers.

CarTech Auto Books & Manuals
800/551-4754

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS Classic Industries
Newest Chevrolet/GMC Truck Catalog

Classic Industries’ newest catalog offers restoration and performance parts and accessories for all 1947-2008 Chevrolet and GMC truck models. At 900 pages, this full-color catalog is the most complete offering of new products for the truck owner and restorer. Notable items in this edition include interior components, upholstery, body components, apparel and accessories for the complete Chevrolet/GMC lifestyle.

Classic Industries
800/854-1280

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Emhart Teknologies
Professional Manual Rivet Tool Kit

Emhart Teknologies has just expanded its line of Pop Nut blind rivet nuts and tools with the addition of two new tool kits — featuring the PNT110 manual tool. The PNT110 is ergonomically designed to fit the user’s hand with contoured grips for comfort. The tool’s quick-change mandrel and nose piece design allow the user the flexibility of setting different size nuts.

Emhart Teknologies
203/924-9341

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Hurst Performance
Special Edition Hurst/Pontiacs

Hurst Performance Vehicles has announced that it has teamed up with newly appointed Hurst Director Emeritus “Doc” Watson to build two new special edition Hurst/Pontiacs—a 2010 Hurst/Pontiac H.O. version of the G8 and a G6 convertible. These numbered cars will feature Hurst’s iconic white/gold and black/gold colors along with forged-alloy Hurst wheels, an exclusive Hurst shifter, a supercharged engine, suspension mods and a specially trimmed interior.

Hurst Performance
949/261-5500

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

K&N Engineering
High-Flow Air Filter for the 2010 Ford Mustang GT 4.6L

According to the company, the K&N high-flow air filter for the 2010 Ford Mustang GT 4.6L V8 (part no. 33-2431) is designed to increase horsepower and acceleration while providing excellent filtration. The simple drop-in design makes it an easy performance Mustang add-on. K&N high-flow replacement filters are installed in minutes and comply with factory warranties. K&N filters can be easily cleaned with the Recharger maintenance kit and will last the life of the vehicle.

K&N Engineering
800/858-3333

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Speedway Motors
Stainless-Steel Batwings

According to Speedway Motors, what sets these batwings apart from the rest are the fully reinforced ½-inch-20 threaded bosses available for attaching a Panhard bar or shock mount. Investment cast from high-quality stainless steel, these beautiful batwings provide a strong and stylish means for attaching a four-bar suspension to your street rod’s front axle.

Speedway Motors
800/979-0122

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Meguiar’s
Ultimate Quick Wax

Meguiar’s unveiled its Ultimate Quik Detailer with hydrophobic polymer technology one year ago. Now the company has done it again with Meguiar’s Ultimate Quik Wax, featuring the same relentless water-beading properties with the added protection of a high-tech, easy-to-apply spray wax. According to Meguiar’s, when Quik Detailer becomes slow to wipe off, its time for a coat of Ultimate Quik Wax.

Meguiar’s
800/347-5700

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Metro Moulded Parts Inc.
Gold Series Vent Window Seals

Seal up the vent-wing window on 1963-64 Ford or Mercury fullsize cars with these premium-quality Gold Series vent window seals from Metro Moulded Rubber Parts. According to the company, these faithful reproductions are manufactured by Metro in the U.S. to the highest quality standards so that they will look correct and function exactly as designed by the OEM back in the day. Part number WR 3363 fits fullsize Ford and Mercury two-door and four-door sedans and station wagon models.

Metro Moulded Parts Inc.
800/878-2237

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Mr. Norm’s Garage
Mopar A-, B- and E-Body Rear
Suspensions

Mr. Norm’s Garage is proud to announce that it is now offering a comprehensive line of easy-to-install rear suspension systems for 1960s and 1970s Mopar A-, B- and E-body musclecars. Designed to fit 1967 thru 1976 A bodies, 1968 thru 1970 and 1971 thru 1974 B bodies and 1970 thru 1974 E bodies, these rear suspension systems by Mr. Norm’s Garage are available in both weld-in and bolt-in styles.

Mr. Norm’s Garage
727/869-9533

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

TMI Products
Mustang Center Consoles

TMI has just released a collection of beautifully crafted center consoles designed specifically for 1965 through 1973 Mustangs. According to TMI, these new centerpieces are a fashionable and extremely convenient addition to any Mustang interior. And you can dress it up or blend the console in by choosing from a wide selection of TMI’s stock style materials and colors or exclusive custom fabrics and tones. Quick and simple to install using hook-and-loop straps, TMI consoles fit directly over the transmission tunnel or OEM factory console.

TMI Products
800/624-7960

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Zex
Dodge Hemi Challenger Nitrous System

According to Zex, the new specially designed wet nitrous system delivers 75 to 175 additional horsepower to 2008-current Dodge Hemi Challengers. The Dodge 5.7L and 6.1L EFI Hemi engines are the perfect platform for nitrous injection upgrades. The Zex nitrous system for the new Dodge Hemi Challenger was extensively engineered for a simple plug-and-play installation and includes custom-designed brackets and a special fuel line adapter that helps finish the installation in only two to three hours.


Zex
888/817-1008
 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Wiley X
Wiley X Eyewear

According to Wiley X, one pair of high-performance Wiley X sunglasses is all any consumer needs, whether driving to work, cruising on the open water, working at a job site or factory or cutting loose on the weekend. The ballistic qualities and fashion-forward designs of Wiley X Eyewear provide comprehensive eye protection with stylish good looks.

Wiley X
800/776-7842

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Scosche
Kia Amanti Installation Kit

Scosche Industries is now shipping its new “custom kit, factory fit” Kia Amanti installation kit. The KA2095B is designed specifically for 2007 and up Kia Amanti vehicles. The KA2095B will accommodate either an ISO single-DIN mount with pocket or an ISO double-DIN mount.

Scosche
800/363-4490

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Omni Lubricants
Green Grease

Green Grease is now available in 55-gallon drums, 16-gallon kegs and 5-gallon pails. This multipurpose synthetic polymer grease is a professional-grade, high-performance grease developed for a multitude of applications. According to Omni, Green Grease really is waterproof, which is better than “water resistant.” The synthetic polymers in Green Grease create a seal that sticks to the metal, protecting bearings (U-joints, tie-rods, etc.) from contaminants, such as dust, sand, grit and dirt.

Omni Lubricants
877/GO-GREASE

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

PML
Big-Block Chevrolet Valve Covers

PML is now shipping tall big-block Chevrolet valve covers with classic Corvette script. According to the company, these tall valve covers feature strong sand-cast aluminum construction, raised Corvette script and fins, and cast-in baffles to prevent oil leaks. These new valve covers are taller than stock to accommodate roller rockers.

PML Inc.
310/671-4345

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Accel (A Div. of Prestolite Performance)
Extreme 9000 Ceramic Wire Kits

Accel now offers the cure for burned sparkplug-wire boots with Extreme 9000 ceramic wire kits. The 8mm ferro-spiral core wire now has ceramic boots that will withstand up to 2,000° F on the sparkplug end of the wires.

Accel
(A Div. of Prestolite Performance)
216/688-8300

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

RHS
Pro Elite SBC 23-Degree CNC-Ported Iron Cylinder Heads

According to RHS, its new SBC 228cc-runner heads provide maximum airflow for circle-track and drag-racing classes that require the use of cast-iron cylinder heads. The precision, accuracy and durability of the RHS heads are derived not only from the precision CNC-porting of the intake and exhaust runners, but the CNC-ported combustion chamber as well.

RHS
877/776-4323

 
Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Advantage Truck Accessories Inc.
2009 Dodge RamBox Tonneau Cover Applications

Advantage Truck Accessories announced tonneau cover applications for the new 2009 Dodge RamBox pickup models. The unique, segment-exclusive cargo management system that features lengthwise storage bins on the outside of the cargo area maintains functionality with the tonneau covers installed. Advantage folding cover models, both the soft TorzaTop and the solid HardHat, may be used in their partial and fully closed positions. Shown is the Advantage TorzaTop installed on the new Dodge Crew Cab with its unique RamBox side storage bins.

Advantage Truck Accessories Inc.
574/293-0979

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Automotive Performance Systems
You Can Do It! In a Job or Your Own
Business…Make Your Life a Success

Bill Neumann is the founder and CEO of Automotive Performance Systems and Neumann Distributing. You Can Do It! is the inspirational story of how Bill accomplished his goals and realized his dreams.

Automotive Performance Systems
805/388-7171

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Carpod
Carpod

Carpod is proud to introduce what the company claims is the most versatile hitch-mounted cargo carrier of its kind. The Carpod easily hitches to the back of a vehicle and features 22-inch sidewalls that can be folded up to keep cargo safe and contained during transport or folded down for ease of storage. Carpod accommodates cargo of up to 450 pounds and 13.25 cubic feet.

Carpod
818/395-8676

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

CarTech Auto Books & Manuals
How to Build Max-Performance Hemi Engines

How to Build Max-Performance Hemi Engines details how to extract more horsepower from second-generation Hemi engines. All of the block options are presented, including street versus race, new versus old and iron versus aluminum. Author Richard Nedbal explores major head types, rocker-arm systems, head machining and prep, valves, springs, seats, porting quench control and more. The book also examines in detail how to install and set up power adders such as nitrous oxide, superchargers and turbochargers.

CarTech Auto Books & Manuals
800/551-4754

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS Classic Industries
Newest Chevrolet/GMC Truck Catalog

Classic Industries’ newest catalog offers restoration and performance parts and accessories for all 1947-2008 Chevrolet and GMC truck models. At 900 pages, this full-color catalog is the most complete offering of new products for the truck owner and restorer. Notable items in this edition include interior components, upholstery, body components, apparel and accessories for the complete Chevrolet/GMC lifestyle.

Classic Industries
800/854-1280

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Emhart Teknologies
Professional Manual Rivet Tool Kit

Emhart Teknologies has just expanded its line of Pop Nut blind rivet nuts and tools with the addition of two new tool kits — featuring the PNT110 manual tool. The PNT110 is ergonomically designed to fit the user’s hand with contoured grips for comfort. The tool’s quick-change mandrel and nose piece design allow the user the flexibility of setting different size nuts.

Emhart Teknologies
203/924-9341

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Hurst Performance
Special Edition Hurst/Pontiacs

Hurst Performance Vehicles has announced that it has teamed up with newly appointed Hurst Director Emeritus “Doc” Watson to build two new special edition Hurst/Pontiacs—a 2010 Hurst/Pontiac H.O. version of the G8 and a G6 convertible. These numbered cars will feature Hurst’s iconic white/gold and black/gold colors along with forged-alloy Hurst wheels, an exclusive Hurst shifter, a supercharged engine, suspension mods and a specially trimmed interior.

Hurst Performance
949/261-5500

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

K&N Engineering
High-Flow Air Filter for the 2010 Ford Mustang GT 4.6L

According to the company, the K&N high-flow air filter for the 2010 Ford Mustang GT 4.6L V8 (part no. 33-2431) is designed to increase horsepower and acceleration while providing excellent filtration. The simple drop-in design makes it an easy performance Mustang add-on. K&N high-flow replacement filters are installed in minutes and comply with factory warranties. K&N filters can be easily cleaned with the Recharger maintenance kit and will last the life of the vehicle.

K&N Engineering
800/858-3333

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Speedway Motors
Stainless-Steel Batwings

According to Speedway Motors, what sets these batwings apart from the rest are the fully reinforced ½-inch-20 threaded bosses available for attaching a Panhard bar or shock mount. Investment cast from high-quality stainless steel, these beautiful batwings provide a strong and stylish means for attaching a four-bar suspension to your street rod’s front axle.

Speedway Motors
800/979-0122

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Meguiar’s
Ultimate Quick Wax

Meguiar’s unveiled its Ultimate Quik Detailer with hydrophobic polymer technology one year ago. Now the company has done it again with Meguiar’s Ultimate Quik Wax, featuring the same relentless water-beading properties with the added protection of a high-tech, easy-to-apply spray wax. According to Meguiar’s, when Quik Detailer becomes slow to wipe off, its time for a coat of Ultimate Quik Wax.

Meguiar’s
800/347-5700

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Metro Moulded Parts Inc.
Gold Series Vent Window Seals

Seal up the vent-wing window on 1963-64 Ford or Mercury fullsize cars with these premium-quality Gold Series vent window seals from Metro Moulded Rubber Parts. According to the company, these faithful reproductions are manufactured by Metro in the U.S. to the highest quality standards so that they will look correct and function exactly as designed by the OEM back in the day. Part number WR 3363 fits fullsize Ford and Mercury two-door and four-door sedans and station wagon models.

Metro Moulded Parts Inc.
800/878-2237

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Mr. Norm’s Garage
Mopar A-, B- and E-Body Rear
Suspensions

Mr. Norm’s Garage is proud to announce that it is now offering a comprehensive line of easy-to-install rear suspension systems for 1960s and 1970s Mopar A-, B- and E-body musclecars. Designed to fit 1967 thru 1976 A bodies, 1968 thru 1970 and 1971 thru 1974 B bodies and 1970 thru 1974 E bodies, these rear suspension systems by Mr. Norm’s Garage are available in both weld-in and bolt-in styles.

Mr. Norm’s Garage
727/869-9533

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

TMI Products
Mustang Center Consoles

TMI has just released a collection of beautifully crafted center consoles designed specifically for 1965 through 1973 Mustangs. According to TMI, these new centerpieces are a fashionable and extremely convenient addition to any Mustang interior. And you can dress it up or blend the console in by choosing from a wide selection of TMI’s stock style materials and colors or exclusive custom fabrics and tones. Quick and simple to install using hook-and-loop straps, TMI consoles fit directly over the transmission tunnel or OEM factory console.

TMI Products
800/624-7960

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Zex
Dodge Hemi Challenger Nitrous System

According to Zex, the new specially designed wet nitrous system delivers 75 to 175 additional horsepower to 2008-current Dodge Hemi Challengers. The Dodge 5.7L and 6.1L EFI Hemi engines are the perfect platform for nitrous injection upgrades. The Zex nitrous system for the new Dodge Hemi Challenger was extensively engineered for a simple plug-and-play installation and includes custom-designed brackets and a special fuel line adapter that helps finish the installation in only two to three hours.


Zex
888/817-1008
 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Wiley X
Wiley X Eyewear

According to Wiley X, one pair of high-performance Wiley X sunglasses is all any consumer needs, whether driving to work, cruising on the open water, working at a job site or factory or cutting loose on the weekend. The ballistic qualities and fashion-forward designs of Wiley X Eyewear provide comprehensive eye protection with stylish good looks.

Wiley X
800/776-7842

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Scosche
Kia Amanti Installation Kit

Scosche Industries is now shipping its new “custom kit, factory fit” Kia Amanti installation kit. The KA2095B is designed specifically for 2007 and up Kia Amanti vehicles. The KA2095B will accommodate either an ISO single-DIN mount with pocket or an ISO double-DIN mount.

Scosche
800/363-4490

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Omni Lubricants
Green Grease

Green Grease is now available in 55-gallon drums, 16-gallon kegs and 5-gallon pails. This multipurpose synthetic polymer grease is a professional-grade, high-performance grease developed for a multitude of applications. According to Omni, Green Grease really is waterproof, which is better than “water resistant.” The synthetic polymers in Green Grease create a seal that sticks to the metal, protecting bearings (U-joints, tie-rods, etc.) from contaminants, such as dust, sand, grit and dirt.

Omni Lubricants
877/GO-GREASE

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

PML
Big-Block Chevrolet Valve Covers

PML is now shipping tall big-block Chevrolet valve covers with classic Corvette script. According to the company, these tall valve covers feature strong sand-cast aluminum construction, raised Corvette script and fins, and cast-in baffles to prevent oil leaks. These new valve covers are taller than stock to accommodate roller rockers.

PML Inc.
310/671-4345

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Accel (A Div. of Prestolite Performance)
Extreme 9000 Ceramic Wire Kits

Accel now offers the cure for burned sparkplug-wire boots with Extreme 9000 ceramic wire kits. The 8mm ferro-spiral core wire now has ceramic boots that will withstand up to 2,000° F on the sparkplug end of the wires.

Accel
(A Div. of Prestolite Performance)
216/688-8300

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

RHS
Pro Elite SBC 23-Degree CNC-Ported Iron Cylinder Heads

According to RHS, its new SBC 228cc-runner heads provide maximum airflow for circle-track and drag-racing classes that require the use of cast-iron cylinder heads. The precision, accuracy and durability of the RHS heads are derived not only from the precision CNC-porting of the intake and exhaust runners, but the CNC-ported combustion chamber as well.

RHS
877/776-4323

 
Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Advantage Truck Accessories Inc.
2009 Dodge RamBox Tonneau Cover Applications

Advantage Truck Accessories announced tonneau cover applications for the new 2009 Dodge RamBox pickup models. The unique, segment-exclusive cargo management system that features lengthwise storage bins on the outside of the cargo area maintains functionality with the tonneau covers installed. Advantage folding cover models, both the soft TorzaTop and the solid HardHat, may be used in their partial and fully closed positions. Shown is the Advantage TorzaTop installed on the new Dodge Crew Cab with its unique RamBox side storage bins.

Advantage Truck Accessories Inc.
574/293-0979

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Automotive Performance Systems
You Can Do It! In a Job or Your Own
Business…Make Your Life a Success

Bill Neumann is the founder and CEO of Automotive Performance Systems and Neumann Distributing. You Can Do It! is the inspirational story of how Bill accomplished his goals and realized his dreams.

Automotive Performance Systems
805/388-7171

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Carpod
Carpod

Carpod is proud to introduce what the company claims is the most versatile hitch-mounted cargo carrier of its kind. The Carpod easily hitches to the back of a vehicle and features 22-inch sidewalls that can be folded up to keep cargo safe and contained during transport or folded down for ease of storage. Carpod accommodates cargo of up to 450 pounds and 13.25 cubic feet.

Carpod
818/395-8676

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

CarTech Auto Books & Manuals
How to Build Max-Performance Hemi Engines

How to Build Max-Performance Hemi Engines details how to extract more horsepower from second-generation Hemi engines. All of the block options are presented, including street versus race, new versus old and iron versus aluminum. Author Richard Nedbal explores major head types, rocker-arm systems, head machining and prep, valves, springs, seats, porting quench control and more. The book also examines in detail how to install and set up power adders such as nitrous oxide, superchargers and turbochargers.

CarTech Auto Books & Manuals
800/551-4754

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS Classic Industries
Newest Chevrolet/GMC Truck Catalog

Classic Industries’ newest catalog offers restoration and performance parts and accessories for all 1947-2008 Chevrolet and GMC truck models. At 900 pages, this full-color catalog is the most complete offering of new products for the truck owner and restorer. Notable items in this edition include interior components, upholstery, body components, apparel and accessories for the complete Chevrolet/GMC lifestyle.

Classic Industries
800/854-1280

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Emhart Teknologies
Professional Manual Rivet Tool Kit

Emhart Teknologies has just expanded its line of Pop Nut blind rivet nuts and tools with the addition of two new tool kits — featuring the PNT110 manual tool. The PNT110 is ergonomically designed to fit the user’s hand with contoured grips for comfort. The tool’s quick-change mandrel and nose piece design allow the user the flexibility of setting different size nuts.

Emhart Teknologies
203/924-9341

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Hurst Performance
Special Edition Hurst/Pontiacs

Hurst Performance Vehicles has announced that it has teamed up with newly appointed Hurst Director Emeritus “Doc” Watson to build two new special edition Hurst/Pontiacs—a 2010 Hurst/Pontiac H.O. version of the G8 and a G6 convertible. These numbered cars will feature Hurst’s iconic white/gold and black/gold colors along with forged-alloy Hurst wheels, an exclusive Hurst shifter, a supercharged engine, suspension mods and a specially trimmed interior.

Hurst Performance
949/261-5500

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

K&N Engineering
High-Flow Air Filter for the 2010 Ford Mustang GT 4.6L

According to the company, the K&N high-flow air filter for the 2010 Ford Mustang GT 4.6L V8 (part no. 33-2431) is designed to increase horsepower and acceleration while providing excellent filtration. The simple drop-in design makes it an easy performance Mustang add-on. K&N high-flow replacement filters are installed in minutes and comply with factory warranties. K&N filters can be easily cleaned with the Recharger maintenance kit and will last the life of the vehicle.

K&N Engineering
800/858-3333

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Speedway Motors
Stainless-Steel Batwings

According to Speedway Motors, what sets these batwings apart from the rest are the fully reinforced ½-inch-20 threaded bosses available for attaching a Panhard bar or shock mount. Investment cast from high-quality stainless steel, these beautiful batwings provide a strong and stylish means for attaching a four-bar suspension to your street rod’s front axle.

Speedway Motors
800/979-0122

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Meguiar’s
Ultimate Quick Wax

Meguiar’s unveiled its Ultimate Quik Detailer with hydrophobic polymer technology one year ago. Now the company has done it again with Meguiar’s Ultimate Quik Wax, featuring the same relentless water-beading properties with the added protection of a high-tech, easy-to-apply spray wax. According to Meguiar’s, when Quik Detailer becomes slow to wipe off, its time for a coat of Ultimate Quik Wax.

Meguiar’s
800/347-5700

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Metro Moulded Parts Inc.
Gold Series Vent Window Seals

Seal up the vent-wing window on 1963-64 Ford or Mercury fullsize cars with these premium-quality Gold Series vent window seals from Metro Moulded Rubber Parts. According to the company, these faithful reproductions are manufactured by Metro in the U.S. to the highest quality standards so that they will look correct and function exactly as designed by the OEM back in the day. Part number WR 3363 fits fullsize Ford and Mercury two-door and four-door sedans and station wagon models.

Metro Moulded Parts Inc.
800/878-2237

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Mr. Norm’s Garage
Mopar A-, B- and E-Body Rear
Suspensions

Mr. Norm’s Garage is proud to announce that it is now offering a comprehensive line of easy-to-install rear suspension systems for 1960s and 1970s Mopar A-, B- and E-body musclecars. Designed to fit 1967 thru 1976 A bodies, 1968 thru 1970 and 1971 thru 1974 B bodies and 1970 thru 1974 E bodies, these rear suspension systems by Mr. Norm’s Garage are available in both weld-in and bolt-in styles.

Mr. Norm’s Garage
727/869-9533

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

TMI Products
Mustang Center Consoles

TMI has just released a collection of beautifully crafted center consoles designed specifically for 1965 through 1973 Mustangs. According to TMI, these new centerpieces are a fashionable and extremely convenient addition to any Mustang interior. And you can dress it up or blend the console in by choosing from a wide selection of TMI’s stock style materials and colors or exclusive custom fabrics and tones. Quick and simple to install using hook-and-loop straps, TMI consoles fit directly over the transmission tunnel or OEM factory console.

TMI Products
800/624-7960

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Zex
Dodge Hemi Challenger Nitrous System

According to Zex, the new specially designed wet nitrous system delivers 75 to 175 additional horsepower to 2008-current Dodge Hemi Challengers. The Dodge 5.7L and 6.1L EFI Hemi engines are the perfect platform for nitrous injection upgrades. The Zex nitrous system for the new Dodge Hemi Challenger was extensively engineered for a simple plug-and-play installation and includes custom-designed brackets and a special fuel line adapter that helps finish the installation in only two to three hours.


Zex
888/817-1008
 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Wiley X
Wiley X Eyewear

According to Wiley X, one pair of high-performance Wiley X sunglasses is all any consumer needs, whether driving to work, cruising on the open water, working at a job site or factory or cutting loose on the weekend. The ballistic qualities and fashion-forward designs of Wiley X Eyewear provide comprehensive eye protection with stylish good looks.

Wiley X
800/776-7842

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Scosche
Kia Amanti Installation Kit

Scosche Industries is now shipping its new “custom kit, factory fit” Kia Amanti installation kit. The KA2095B is designed specifically for 2007 and up Kia Amanti vehicles. The KA2095B will accommodate either an ISO single-DIN mount with pocket or an ISO double-DIN mount.

Scosche
800/363-4490

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Omni Lubricants
Green Grease

Green Grease is now available in 55-gallon drums, 16-gallon kegs and 5-gallon pails. This multipurpose synthetic polymer grease is a professional-grade, high-performance grease developed for a multitude of applications. According to Omni, Green Grease really is waterproof, which is better than “water resistant.” The synthetic polymers in Green Grease create a seal that sticks to the metal, protecting bearings (U-joints, tie-rods, etc.) from contaminants, such as dust, sand, grit and dirt.

Omni Lubricants
877/GO-GREASE

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

PML
Big-Block Chevrolet Valve Covers

PML is now shipping tall big-block Chevrolet valve covers with classic Corvette script. According to the company, these tall valve covers feature strong sand-cast aluminum construction, raised Corvette script and fins, and cast-in baffles to prevent oil leaks. These new valve covers are taller than stock to accommodate roller rockers.

PML Inc.
310/671-4345

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Accel (A Div. of Prestolite Performance)
Extreme 9000 Ceramic Wire Kits

Accel now offers the cure for burned sparkplug-wire boots with Extreme 9000 ceramic wire kits. The 8mm ferro-spiral core wire now has ceramic boots that will withstand up to 2,000° F on the sparkplug end of the wires.

Accel
(A Div. of Prestolite Performance)
216/688-8300

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

RHS
Pro Elite SBC 23-Degree CNC-Ported Iron Cylinder Heads

According to RHS, its new SBC 228cc-runner heads provide maximum airflow for circle-track and drag-racing classes that require the use of cast-iron cylinder heads. The precision, accuracy and durability of the RHS heads are derived not only from the precision CNC-porting of the intake and exhaust runners, but the CNC-ported combustion chamber as well.

RHS
877/776-4323

 
Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Advantage Truck Accessories Inc.
2009 Dodge RamBox Tonneau Cover Applications

Advantage Truck Accessories announced tonneau cover applications for the new 2009 Dodge RamBox pickup models. The unique, segment-exclusive cargo management system that features lengthwise storage bins on the outside of the cargo area maintains functionality with the tonneau covers installed. Advantage folding cover models, both the soft TorzaTop and the solid HardHat, may be used in their partial and fully closed positions. Shown is the Advantage TorzaTop installed on the new Dodge Crew Cab with its unique RamBox side storage bins.

Advantage Truck Accessories Inc.
574/293-0979

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Automotive Performance Systems
You Can Do It! In a Job or Your Own
Business…Make Your Life a Success

Bill Neumann is the founder and CEO of Automotive Performance Systems and Neumann Distributing. You Can Do It! is the inspirational story of how Bill accomplished his goals and realized his dreams.

Automotive Performance Systems
805/388-7171

 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Carpod
Carpod

Carpod is proud to introduce what the company claims is the most versatile hitch-mounted cargo carrier of its kind. The Carpod easily hitches to the back of a vehicle and features 22-inch sidewalls that can be folded up to keep cargo safe and contained during transport or folded down for ease of storage. Carpod accommodates cargo of up to 450 pounds and 13.25 cubic feet.

Carpod
818/395-8676

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

CarTech Auto Books & Manuals
How to Build Max-Performance Hemi Engines

How to Build Max-Performance Hemi Engines details how to extract more horsepower from second-generation Hemi engines. All of the block options are presented, including street versus race, new versus old and iron versus aluminum. Author Richard Nedbal explores major head types, rocker-arm systems, head machining and prep, valves, springs, seats, porting quench control and more. The book also examines in detail how to install and set up power adders such as nitrous oxide, superchargers and turbochargers.

CarTech Auto Books & Manuals
800/551-4754

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS Classic Industries
Newest Chevrolet/GMC Truck Catalog

Classic Industries’ newest catalog offers restoration and performance parts and accessories for all 1947-2008 Chevrolet and GMC truck models. At 900 pages, this full-color catalog is the most complete offering of new products for the truck owner and restorer. Notable items in this edition include interior components, upholstery, body components, apparel and accessories for the complete Chevrolet/GMC lifestyle.

Classic Industries
800/854-1280

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Emhart Teknologies
Professional Manual Rivet Tool Kit

Emhart Teknologies has just expanded its line of Pop Nut blind rivet nuts and tools with the addition of two new tool kits — featuring the PNT110 manual tool. The PNT110 is ergonomically designed to fit the user’s hand with contoured grips for comfort. The tool’s quick-change mandrel and nose piece design allow the user the flexibility of setting different size nuts.

Emhart Teknologies
203/924-9341

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Hurst Performance
Special Edition Hurst/Pontiacs

Hurst Performance Vehicles has announced that it has teamed up with newly appointed Hurst Director Emeritus “Doc” Watson to build two new special edition Hurst/Pontiacs—a 2010 Hurst/Pontiac H.O. version of the G8 and a G6 convertible. These numbered cars will feature Hurst’s iconic white/gold and black/gold colors along with forged-alloy Hurst wheels, an exclusive Hurst shifter, a supercharged engine, suspension mods and a specially trimmed interior.

Hurst Performance
949/261-5500

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

K&N Engineering
High-Flow Air Filter for the 2010 Ford Mustang GT 4.6L

According to the company, the K&N high-flow air filter for the 2010 Ford Mustang GT 4.6L V8 (part no. 33-2431) is designed to increase horsepower and acceleration while providing excellent filtration. The simple drop-in design makes it an easy performance Mustang add-on. K&N high-flow replacement filters are installed in minutes and comply with factory warranties. K&N filters can be easily cleaned with the Recharger maintenance kit and will last the life of the vehicle.

K&N Engineering
800/858-3333

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Speedway Motors
Stainless-Steel Batwings

According to Speedway Motors, what sets these batwings apart from the rest are the fully reinforced ½-inch-20 threaded bosses available for attaching a Panhard bar or shock mount. Investment cast from high-quality stainless steel, these beautiful batwings provide a strong and stylish means for attaching a four-bar suspension to your street rod’s front axle.

Speedway Motors
800/979-0122

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Meguiar’s
Ultimate Quick Wax

Meguiar’s unveiled its Ultimate Quik Detailer with hydrophobic polymer technology one year ago. Now the company has done it again with Meguiar’s Ultimate Quik Wax, featuring the same relentless water-beading properties with the added protection of a high-tech, easy-to-apply spray wax. According to Meguiar’s, when Quik Detailer becomes slow to wipe off, its time for a coat of Ultimate Quik Wax.

Meguiar’s
800/347-5700

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Metro Moulded Parts Inc.
Gold Series Vent Window Seals

Seal up the vent-wing window on 1963-64 Ford or Mercury fullsize cars with these premium-quality Gold Series vent window seals from Metro Moulded Rubber Parts. According to the company, these faithful reproductions are manufactured by Metro in the U.S. to the highest quality standards so that they will look correct and function exactly as designed by the OEM back in the day. Part number WR 3363 fits fullsize Ford and Mercury two-door and four-door sedans and station wagon models.

Metro Moulded Parts Inc.
800/878-2237

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Mr. Norm’s Garage
Mopar A-, B- and E-Body Rear
Suspensions

Mr. Norm’s Garage is proud to announce that it is now offering a comprehensive line of easy-to-install rear suspension systems for 1960s and 1970s Mopar A-, B- and E-body musclecars. Designed to fit 1967 thru 1976 A bodies, 1968 thru 1970 and 1971 thru 1974 B bodies and 1970 thru 1974 E bodies, these rear suspension systems by Mr. Norm’s Garage are available in both weld-in and bolt-in styles.

Mr. Norm’s Garage
727/869-9533

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

TMI Products
Mustang Center Consoles

TMI has just released a collection of beautifully crafted center consoles designed specifically for 1965 through 1973 Mustangs. According to TMI, these new centerpieces are a fashionable and extremely convenient addition to any Mustang interior. And you can dress it up or blend the console in by choosing from a wide selection of TMI’s stock style materials and colors or exclusive custom fabrics and tones. Quick and simple to install using hook-and-loop straps, TMI consoles fit directly over the transmission tunnel or OEM factory console.

TMI Products
800/624-7960

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Zex
Dodge Hemi Challenger Nitrous System

According to Zex, the new specially designed wet nitrous system delivers 75 to 175 additional horsepower to 2008-current Dodge Hemi Challengers. The Dodge 5.7L and 6.1L EFI Hemi engines are the perfect platform for nitrous injection upgrades. The Zex nitrous system for the new Dodge Hemi Challenger was extensively engineered for a simple plug-and-play installation and includes custom-designed brackets and a special fuel line adapter that helps finish the installation in only two to three hours.


Zex
888/817-1008
 

SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Wiley X
Wiley X Eyewear

According to Wiley X, one pair of high-performance Wiley X sunglasses is all any consumer needs, whether driving to work, cruising on the open water, working at a job site or factory or cutting loose on the weekend. The ballistic qualities and fashion-forward designs of Wiley X Eyewear provide comprehensive eye protection with stylish good looks.

Wiley X
800/776-7842

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

Scosche
Kia Amanti Installation Kit

Scosche Industries is now shipping its new “custom kit, factory fit” Kia Amanti installation kit. The KA2095B is designed specifically for 2007 and up Kia Amanti vehicles. The KA2095B will accommodate either an ISO single-DIN mount with pocket or an ISO double-DIN mount.

Scosche
800/363-4490

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Omni Lubricants
Green Grease

Green Grease is now available in 55-gallon drums, 16-gallon kegs and 5-gallon pails. This multipurpose synthetic polymer grease is a professional-grade, high-performance grease developed for a multitude of applications. According to Omni, Green Grease really is waterproof, which is better than “water resistant.” The synthetic polymers in Green Grease create a seal that sticks to the metal, protecting bearings (U-joints, tie-rods, etc.) from contaminants, such as dust, sand, grit and dirt.

Omni Lubricants
877/GO-GREASE

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS 

PML
Big-Block Chevrolet Valve Covers

PML is now shipping tall big-block Chevrolet valve covers with classic Corvette script. According to the company, these tall valve covers feature strong sand-cast aluminum construction, raised Corvette script and fins, and cast-in baffles to prevent oil leaks. These new valve covers are taller than stock to accommodate roller rockers.

PML Inc.
310/671-4345

 
 SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

Accel (A Div. of Prestolite Performance)
Extreme 9000 Ceramic Wire Kits

Accel now offers the cure for burned sparkplug-wire boots with Extreme 9000 ceramic wire kits. The 8mm ferro-spiral core wire now has ceramic boots that will withstand up to 2,000° F on the sparkplug end of the wires.

Accel
(A Div. of Prestolite Performance)
216/688-8300

 
SEMA NEWS-SEPTEMBER 2009-NEW PRODUCTS

RHS
Pro Elite SBC 23-Degree CNC-Ported Iron Cylinder Heads

According to RHS, its new SBC 228cc-runner heads provide maximum airflow for circle-track and drag-racing classes that require the use of cast-iron cylinder heads. The precision, accuracy and durability of the RHS heads are derived not only from the precision CNC-porting of the intake and exhaust runners, but the CNC-ported combustion chamber as well.

RHS
877/776-4323

 
Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA Trade Shows Director

SEMA NEWS-OCTOBER 2009-INSIDE SEMA-GARY VIGILSEMA News: Can you briefly explain your role and the role of your department at SEMA?

Gary Vigil: One of the ways SEMA tries to fulfill its mission of helping its members’ businesses succeed and prosper is to produce the industry’s leading trade show. Thanks to the loyalty of SEMA-member companies and the dedication of staff, the SEMA Show has become a truly world-class event. The SEMA staff, along with the support of ConvExx Show Management, plays an important role in delivering a successful Show to exhibitors and Show attendees. The staff is aware that SEMA members have limited marketing budgets and have many options on which to spend their money. So when they put their trust in SEMA by their participation and support of the SEMA Show, the staff works to ensure that they get a great return on their investments. The staff takes pride in providing great customer service and in creating programs that address the needs of the association’s members.

SN: The 2009 SEMA Show is less than 100 days away. What can attendees expect from this year’s Show?

GV: Attendees at the 2009 SEMA Show can expect what they’re accustomed to getting at a SEMA-produced event: the industry’s leading manufacturers, a world-class New Products Showcase with cutting-edge products, an incredible display of customized vehicles, high-quality educational programs, great special events, and plenty of networking opportunities. In addition, this year’s SEMA Show will include two new Show sections: Paint, Body & Equipment and Powersports & Utility Vehicles.

SN: What are some of the challenges and opportunities related to this year’s Show?

GV: The economy has certainly created some unique challenges this year. Most companies have smaller budgets to work with and are looking for the most effective use of their limited dollars. More exhibitors have looked to us this year to find ways for them to exhibit more affordably. With the assistance of ConvExx Show Management and our partners, such as Freeman, we have been able to provide exhibitors with lower-cost options that still enable them to accomplish their objectives. I believe that we’ll see better pre-show planning by exhibitors and attendees this year, and I expect there to be very productive meetings at the Show, as both exhibitors and buyers will be looking for those business partnerships and opportunities that will help them to generate revenues.

SN: The association says that it continues to look for ways to add value to participants’ Show experiences. Can you highlight some of the programs and services that have been created to meet that goal?

GV: In the 15 years that I’ve worked at SEMA, I can’t recall a more concerted effort among the staff and the association’s partners to create value-added programs for exhibitors and attendees. In order to make it easier and more affordable for Southern California buyers to attend, SEMA has created a Buyer Bus Program, which will be transporting buyers from key Southern California cities directly to the Las Vegas Convention Center. For only $25, buses will pick up buyers Tuesday morning and return them on Wednesday evening.

Working with hotel partners, SEMA has been able to make available discounted rooms at dozens of hotels—with most rates 25% to 45% lower than last year. Turnkey discounted booth packages can save exhibitors up to 30% off booth services, and SEMA is providing an online matchmaking tool that enables exhibiting manufacturers to connect with buyers before, during and after the SEMA Show. The matchmaking program pairs exhibitors with buyers, prioritizing them by relevance based on their common product interests. As part of the matchmaking program, eligible exhibitors are guaranteed 1,000 matches or they may request to withdraw from the Show and receive their money back.

In addition, SEMA Show exhibitors will benefit by receiving a bonus seniority point this year, which will benefit them in their booth location selection in future years. Exhibitors who signed up before the space selection were given the opportunity to pay only 25% deposit if paying by credit card. Last year, a minimum 50% deposit was required. Exhibitors with at least five years’ seniority were offered a payment option that would allow them to extend their final payment to May, 2010. In previous years, all exhibitors were required to pay months before the Show opened.

SN: Is there anything else you would like to relate to the membership?

GV: SEMA remains committed to delivering value and return on investment to its members. We’re constantly trying to understand our members’ greatest challenges and needs and striving to improve the Show so that it meets or exceeds those expectations.

Tue, 09/01/2009 - 17:21

SEMA News - September 2009

SEMA Trade Shows Director

SEMA NEWS-OCTOBER 2009-INSIDE SEMA-GARY VIGILSEMA News: Can you briefly explain your role and the role of your department at SEMA?

Gary Vigil: One of the ways SEMA tries to fulfill its mission of helping its members’ businesses succeed and prosper is to produce the industry’s leading trade show. Thanks to the loyalty of SEMA-member companies and the dedication of staff, the SEMA Show has become a truly world-class event. The SEMA staff, along with the support of ConvExx Show Management, plays an important role in delivering a successful Show to exhibitors and Show attendees. The staff is aware that SEMA members have limited marketing budgets and have many options on which to spend their money. So when they put their trust in SEMA by their participation and support of the SEMA Show, the staff works to ensure that they get a great return on their investments. The staff takes pride in providing great customer service and in creating programs that address the needs of the association’s members.

SN: The 2009 SEMA Show is less than 100 days away. What can attendees expect from this year’s Show?

GV: Attendees at the 2009 SEMA Show can expect what they’re accustomed to getting at a SEMA-produced event: the industry’s leading manufacturers, a world-class New Products Showcase with cutting-edge products, an incredible display of customized vehicles, high-quality educational programs, great special events, and plenty of networking opportunities. In addition, this year’s SEMA Show will include two new Show sections: Paint, Body & Equipment and Powersports & Utility Vehicles.

SN: What are some of the challenges and opportunities related to this year’s Show?

GV: The economy has certainly created some unique challenges this year. Most companies have smaller budgets to work with and are looking for the most effective use of their limited dollars. More exhibitors have looked to us this year to find ways for them to exhibit more affordably. With the assistance of ConvExx Show Management and our partners, such as Freeman, we have been able to provide exhibitors with lower-cost options that still enable them to accomplish their objectives. I believe that we’ll see better pre-show planning by exhibitors and attendees this year, and I expect there to be very productive meetings at the Show, as both exhibitors and buyers will be looking for those business partnerships and opportunities that will help them to generate revenues.

SN: The association says that it continues to look for ways to add value to participants’ Show experiences. Can you highlight some of the programs and services that have been created to meet that goal?

GV: In the 15 years that I’ve worked at SEMA, I can’t recall a more concerted effort among the staff and the association’s partners to create value-added programs for exhibitors and attendees. In order to make it easier and more affordable for Southern California buyers to attend, SEMA has created a Buyer Bus Program, which will be transporting buyers from key Southern California cities directly to the Las Vegas Convention Center. For only $25, buses will pick up buyers Tuesday morning and return them on Wednesday evening.

Working with hotel partners, SEMA has been able to make available discounted rooms at dozens of hotels—with most rates 25% to 45% lower than last year. Turnkey discounted booth packages can save exhibitors up to 30% off booth services, and SEMA is providing an online matchmaking tool that enables exhibiting manufacturers to connect with buyers before, during and after the SEMA Show. The matchmaking program pairs exhibitors with buyers, prioritizing them by relevance based on their common product interests. As part of the matchmaking program, eligible exhibitors are guaranteed 1,000 matches or they may request to withdraw from the Show and receive their money back.

In addition, SEMA Show exhibitors will benefit by receiving a bonus seniority point this year, which will benefit them in their booth location selection in future years. Exhibitors who signed up before the space selection were given the opportunity to pay only 25% deposit if paying by credit card. Last year, a minimum 50% deposit was required. Exhibitors with at least five years’ seniority were offered a payment option that would allow them to extend their final payment to May, 2010. In previous years, all exhibitors were required to pay months before the Show opened.

SN: Is there anything else you would like to relate to the membership?

GV: SEMA remains committed to delivering value and return on investment to its members. We’re constantly trying to understand our members’ greatest challenges and needs and striving to improve the Show so that it meets or exceeds those expectations.